Catálogos >
TWK-ELEKTRONIK GmbH >
Rotary encoder HBN/S3 SIL2

Rotary encoder HBN/S3 SIL2
1 / 16Páginas

Excertos do catálogo

■ Robust design for rough applications with high resolution requirement such as crane technology, construction machines and special engineering ■ High vibration and shock resistance thanks to the compact mechanical design ■ Resolution < 22 bit / 360° ■ Speed signal in digits/ms with variable gate time ■ Protection type IP 66 Design - Robust housing (wall thickness 5 mm) manufactured from seawater-proof aluminium (AlMgSi1) or stainless steel (material: 1.4305 optionally 1.4404). - Position recording and evaluation are of a redundant design to implement a reliable position value and speed signal. - A network in/out module with transient filtering, voltage supply and output driver unit forms the electrical interface. - Electrical connection via two M12 connectors, 5-pin, pin and socket for bus IN / bus OUT. Function A correct mechanical connection between the customer and sensor shaft ensures that the sensor precisely detects the customer shaft's rotations. A safe position is provided by the plausibility check of two sensor systems. Detected errors are evaluated. The CAN interface outputs the validated position value and speed signal via the CANopen Safety protocol within an SRDO (Safety Relevant Data Object) using 2x2 messages (normal and inverted). The rotary encoder meets the conditions of safety level SIL2 according to IEC 61508 and performance level "d" according to EN13849. The prerequisite of safety-relevant operation is a failsafe master. TWK-ELEKTRONIK GmbH Heinrichstrasse 85 info@twk.de www.twk.de

Abrir o catálogo na página 1

Technical data Electrical data ■ Operating voltage: ■ Power consumption: ■ Resolution: ■ Code direction: ■ Reference value: ■ Accuracy: ■ Reproducibility: ■ Temperature drift: ■ CAN IC voltage rating: 9 to 36 VDC (protected against polarity reversal) < 1.8 W 16 bit (for higher resolution, please contact our technical staff) CW* or CCW** can be set 0 to (total number of steps -1) < ± 0.05 % (with reference to 360°) < ± 0.01 % (with reference to 360°) < 0.1 % (with reference to 360° over the entire temperature range) Maximum common mode votage -7 to +12 V Maximum allowed voltage at pins ±36 V...

Abrir o catálogo na página 2

Absolute single-turn rotary encoder with high resolution Model HBN Technical data System in general and Safety  Slew rate power supply:  Time of storage cycles:  Time between error recognition and alarm (emergency message): 100 ms (power supply) 5 s (RAM test, single bit error) 2 s (ROM test during setup time) Principle circuit diagram Sensor systems Galvanic separation Digital isolator Switching power supply Voltage monitoring

Abrir o catálogo na página 3

Interface according to the following specifications CiA DS301 CANopen Application Layer and Communication Profile, Version 4.1 EN 50325-5 (CIA DS304) CANopen Framework for safety-relevant communication, Version 1.0.1 CiA DS305 CANopen - Layer Setting Services and Protocol (LSS) CiA DS406 CANopen - Device Profile for Encoders, Version 4.0.1 IEC 61508 Functional safety of safety-related electrical/programmable electronic systems. Supply source for the listed CANopen specifications: CAN in Automation (CiA), Kontumazgarten 3, D-90429 Nurnberg, (E-mail: headquarters@can-cia.org, www.can-cia.org)...

Abrir o catálogo na página 4

Absolute single-turn rotary encoder with high resolution Model HBN Bus termination, output level Further CANopen Subscriber TWK-CANopen Subscriber CAN-Bus CAN_L Output level according to ISO/DIS 11898 With common mode voltage = 0 V

Abrir o catálogo na página 5

Date: 03.04.2018 Page 6 of 16 Document no. HBN 13218 GE

Abrir o catálogo na página 6

Electrical connection ■ Two round connectors M12x1, pin and socket for bus IN/OUT, 5-pin, A-coded ■ Refer to the tables below for the connection assignments; these are also enclosed with the devices. Mating connectors (to be ordered separately) All of the mating connectors listed in the following table are M12X1, 5-pin, A-coded, with screw clamp connection, with protection type IP 67, with screening on the housing and the maximum connection cross-section is 0.75 mm2. Please note: if angled mating connectors are used, please notify us so that the device connectors can be aligned accordingly....

Abrir o catálogo na página 7

Note: This is the contact assignment for the standard version. Other versions may have a different contact assignment. In this case, please observe connection assignment TY enclosed with each device. Different M12 connector combinations or assignments are possible at the request of the customer. For the following description and pictorials is valid: Viewed looking at the PIN side of the connector installed in the HBN. There is one connector for Bus-In and Bus-Out each for the HBN. If there is only Bus-In, the female connector Bus-Out is omitted. Important: The recommended version is V1 with...

Abrir o catálogo na página 8

HBN 58 - K A 65,536 R S3 S V1 N 01 Electrical and mechanical variants * 01 Standard Output: N CANopen Galvanic sepration (#). See page 8: V1 -VS # CAN_GND # screening/housing (recommended version) V2 -VS = CAN_GND # screening/housing V3 -VS = CAN_GND = screening/housing Electrical connection: S M12 connector (bus in/bus out) Kx Cable, x=length in m Profile: C3 CANopen according to CIA, DS 406 revision 4.0.1 S3 CANopen Safety SIL2 Code: R Binary Resolution: Housing material: A Aluminium S Stainless steel Flange type: K Clamped flange, shaft 10 mm with flattened area KF Clamped flange, shaft...

Abrir o catálogo na página 9

Absolute single-turn rotary encoder with high resolution Model HBN Installation drawing Standard design form: clamped flange, shaft 10 mm with flattened area Order number: HBN58 - KA 65,536 R S3 S N01 NILOS ring Bus In Sensor connector M12 5-pole pins, A-coded aligned Bus Out Sensor connector M12 5-pole socket, A-coded aligned Coding groove Coding pin

Abrir o catálogo na página 10

Absolute single-turn rotary encoder with high resolution Model HBN Installation drawing Further possible design form: clamped flange, shaft 10 mm with woodruff key Order number: HBN58 - KFA 65,536 R S3 S N01 NILOS ring Bus In Sensor connector M12 5-pole pins, A-coded aligned Bus Out Sensor connector M12 5-pole socket, A-coded aligned Coding groove Coding pin

Abrir o catálogo na página 11

Rotary encoder HBN/S3 SIL2 1 / 16Páginas

Excertos do catálogo

Todos os catálogos e folhetos técnicos TWK-ELEKTRONIK GmbH

Rotary encoder HBN/S3 SIL2
1 / 16Páginas