Catálogos >
SHENZHEN RION TECHNOLOGY CO.,LTD >
Rion angle level switch LCA341&LCA342

Rion angle level switch LCA341&LCA342
1 / 10Páginas

Excertos do catálogo

Rion angle level switch LCA341&LCA342 - 1

LCA341/342 RELAY OUTPUT TYPE TILT SWITCH Appearance Patent No: 201830752874.1 RoSH certification: 18300RC20410801 V1.4 RELAY OUTPUT TYPE TILT SWITCH

Abrir o catálogo na página 1

Rion angle level switch LCA341&LCA342 - 2

LCA341/342 RELAY OUTPUT TYPE TILT SWITCH ○ RoHS certification:18300RC20410801 ○ China National Intellectual Property Appearance Patent (Patent No : 201830752874.1) ○ Revision time:2023-10-27 Note: Product functions, parameters, appearance, etc. will be adjusted as the technology upgrades. Please contact our pre-sales business to confirm when purchasing. Disclaimer This product is developed exclusively for commercial applications and is prohibited from being used for illegal purposes, such as military activities, research related to nuclear, chemical, or biological weapons, or any other...

Abrir o catálogo na página 2

Rion angle level switch LCA341&LCA342 - 3

LCA341/342 RELAY OUTPUT TYPE TILT SWITCH ▶ GENERAL DESCRIPTION LCA341A series a low cost tilt switch developed by RION for application like level safety alarming and platform level monitor and alarm. There is relay output circuit inside. Alarm threshold value is pre-stable. when the inclination exceed set alarm value, it will output relay output signal(drive current 1A) to drive the solenoid valve hydraulic system or drive buzzer or alarming light for the safety of platform. Its main function is to monitor and alarm the(dual axis or single axis) inclination of platform automatically. It is...

Abrir o catálogo na página 3

Rion angle level switch LCA341&LCA342 - 4

LCA341/342 RELAY OUTPUT TYPE TILT SWITCH Measure accuracy Long-term stability Measure range Measure axis Zero temp. coeffiecient Temp. Sensitivity coefficient Power on time Response time Electromagnetic compatibility MTBF ≥100MΩ 100g@11ms、3 axial direction (half sinusoid) Impact resistance Insulation Resistance Protection grade 10grms、10～1000Hz Direct lead IP67; Aviation plug IP65 1m, durable, grease proof, wide temperature, shield cable, 4*0.4 mm2 140g(without cable) KEY WORDS RESOLUTION: the smallest change value that the sensor can detect and distinguish within the measurement range....

Abrir o catálogo na página 4

Rion angle level switch LCA341&LCA342 - 5

LCA341/342 RELAY OUTPUT TYPE TILT SWITCH E.g: LCA341A-F005 : single axis/1 way output /replay NO Output/0.5° alarm. NOTE: 1) please place order according to the order description; 2) The factory default alarm threshold value is ±2°, if other value required, please order refer to the order information; 3) Explanation: N(normal close)- it is normal close when inclination within threshold value and change to normal open when exceeds threshold value; F(normal open)- it is normal open when inclination within threshold value and change to normal close when exceeds threshold value. ▶ MECHANICAL...

Abrir o catálogo na página 5

Rion angle level switch LCA341&LCA342 - 6

LCA341/342 RELAY OUTPUT TYPE TILT SWITCH Note: 1) RXD and TXD two lines can be used to connect to the computer, through the software to set the alarm threshold. 2) there is no preset angle value function for dual axes double wires 3) connection of RXD and TXD function, see below drawing. 4) If you are using a laptop debugging you also need a RS232 to USB module, if the PC can be directly connected communication with the computer COM port.( If use converter must install conversion module driver can be use) The above diagram shows the working principle of a dual axis switch. The output signal...

Abrir o catálogo na página 6

Rion angle level switch LCA341&LCA342 - 7

LCA341/342 RELAY OUTPUT TYPE TILT SWITCH Size : L60 x W60 x H36MM Installation size: L48 x W48 x H4mm Mounting screws: 4 M4 screws ▶ MEASURE DIRECTIONS&FIX The installation must guarantee the product bottom is parallel to measured face，and reduce the influence of dynamic and acceleration to the sensor. This product can be installed horizontally or mounted vertically (mounted vertically selection is only applicable to the single axis, and only can do relative measurement , if absolute measurement the level reference will occur error ), for installation please refer to the following scheme. ▶...

Abrir o catálogo na página 7

Rion angle level switch LCA341&LCA342 - 8

LCA341/342 RELAY OUTPUT TYPE TILT SWITCH ▶ RION PRODUCT DEBUGGING SOFTWARE If you want to change the alarm thresholds, can communicate with computer and use the serial debugging assistant software to change . Your can download the common public serial port debugging assistant software on line, Rion’s products supporting debugging software can connect the inclinometer by itself on computer and display the angle , also can download the public serial port debugging software on line !

Abrir o catálogo na página 8

Rion angle level switch LCA341&LCA342 - 9

LCA341/342 RELAY OUTPUT TYPE TILT SWITCH Debug process: 1) Open software; 2) Select the corresponding COM port, refer to 2”. 3) Other settings are default setting , no need to set. " 4) Click to open the serial port button, refer to 2 " 5) This data will display in the return data area, refer to 3” 6) If you want to set the alarm threshold, please input setting alarm threshold command in input area, refer to 4" . ( For command please refer to the specification of communication protocol .) 7) When the return data area display " command +Okay" proved successful setting. Refer to 5” Common...

Abrir o catálogo na página 9

Rion angle level switch LCA341&LCA342 - 10

LCA341/342 RELAY OUTPUT TYPE TILT SWITCH The current position is relative ZERO, related data will be stored in EEPROM, and carry out relative angle output , after accepting command then output :“set relative zero” . The absolute angle output , after accepting command then output: “absolute &R zero”. Setting positive half axis of X axis to be alarm point,“????” is angle value ， *xp=???? optional value from “0001—1000”. The default is 0150。After accepting command then output: “SetxP OK!” *xn=????―― Setting negative half axis of X axis to be alarm point,“????” is *xn=???? angle value ，...

Abrir o catálogo na página 10