Catálogos >
Panasonic Robot & Welding system solutions >
POSCAP

POSCAP
1 / 40Páginas

Adicionar aos Favoritos

Excertos do catálogo

2020 Conductive Polymer Tantalum Solid Capacitors Products Catalog g

Abrir o catálogo na página 1

■ If you want to use our products described in this online catalog for applications requiring special qualities or reliability, or for applications where the failure or malfunction of the products may directly jeopardize human life or potentially cause personal injury (e.g. aircraft and aerospace equipment, traffic and transportation equipment, combustion equipment, medical equipment, accident prevention, anti-crime equipment, and/or safety equipment), it is necessary to verify whether the specifications of our products fit to such applications. Please ensure that you will ask and check...

Abrir o catálogo na página 2

Notices / Items to be observed Notices ■ Applicable laws and regulations ・This product complies with the RoHS Directive (Restriction of the use of certain hazardous substances in electrical and electronic equipment (DIRECTIVE 2011/65/EU and（EU)2015/863)). ・ No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in producing this product. 　We do not use PBBs or PBDEs as brominated flame retardants. ・ Export procedure which followed export related regulations, such as foreign exchange and a foreign trade method, on the occasion of export of this...

Abrir o catálogo na página 3

Conductive Polymer Tantalum Solid Capacitors 　　Guidelines and precautions（POSCAP） 1. Circuit design 1.1 Prohibited circuits Since problems can be expected, POSCAP cannot be used on the following circuits. (1) High impedance voltage retention circuits (2) Coupling circuit (3) Time constant circuits (4) Circuits greatly affected by leakage current (5) The circuit in which two or more POSCAP are connected in a series so as to raise the endurance voltage. 1.2 Failure and life-span The failure rate is 0.5 %* / 1000 h (Confidence level : 60 %) based on JIS C 5003. The mainly failure modes are as...

Abrir o catálogo na página 4

Panasonic industry Conductive Polymer Tantalum Solid Capacitors 1.6 Leakage current Even when the soldering conditions fall within the range of this delivery specifications, leakage current increases a little on occasion. It also increases a little during high temperature storage, high humidity storage £and temperature cycling with no voltage applied. In cases such as these, leakage current will decrease by applying voltage under the condition of below the POSCAP's maximum operating temperature. The speed at which the leakage current is restored is increased by applying voltage when the...

Abrir o catálogo na página 5

Panasonic industry Conductive Polymer Tantalum Solid Capacitors

Abrir o catálogo na página 6

Panasonic industry Conductive Polymer Tantalum Solid Capacitors

Abrir o catálogo na página 7

Conductive Polymer Tantalum Solid Capacitors Diagram Small size Low profile Large capacitance High reliability High reliability Guaranteed at 125℃ Low ESR Small size Large capacitance Small size Low profile Large capacitance TQS High voltage Small size Low profile ★Not Recomm

Abrir o catálogo na página 8

Panasonic industry Conductive Polymer Tantalum Solid Capacitors

Abrir o catálogo na página 9

Conductive Polymer Tantalum Solid Capacitors Mounting specifications ◇ Recommendable reflow soldering The cycles of reflow soldering : Twice (max.) 〈Peak temperature 250 ℃ lead free reflow soldering profile〉 Temperature on the surface of capacitor Temperature on the surface of capacitor 〈 Recommended reflow soldering temperature profile 〉 The cycles of reflow soldering : Twice (max.) The model of MSL “2a” is changed into MSL “3” with this reflow condition. 〈 TQC / TQS series 〉 Temperature on the surface of capacitor Temperature on the surface of capacitor Soldering time Soldering time...

Abrir o catálogo na página 10

Panasonic industry Conductive Polymer Tantalum Solid Capacitors O Dimension of carrier tape Size code Size code

Abrir o catálogo na página 11

Panasonic INDUSTRY Surface Mount Type TPG series Conductive Polymer Tantalum Solid Capacitors ^ ^ poscApFeatures • Small size, Low profile (L 3.5 x W 2.8 x H 1.1 mm) • Large capacitance (220 |jF max.) • RoHS compliance, Halogen free Size code *1: Ripple current(100 kHz / +45 °C) *2: ESR(100 kHz / +20 °C) *3: tan 5 (120 Hz / +20 °C) *4: After 5 minutes ♦ Please refer to each page in this catarog for "Reflow conditions" /'Taping specifications" and "Floor life level" . Design and specifications are each subject to change without notice. Ask factory for the current technical specifications...

Abrir o catálogo na página 12

NEW Surface Mount Type TPS series Conductive Polymer Tantalum Solid Capacitors ^ ^ poscAp Features • 105 T 2000 h • Small size, Low profile (L 3.5 x W 2.8 x H 1.2 mm max.) • RoHS compliance, Halogen free Characteristics list Rated voltage (V) *1: Ripple current (100 kHz / +45 T) *2: ESR (100 kHz / +20 T) *3: tan 5 (120 Hz / +20 T) *4: After 5 minutes ♦ Please refer to each page in this catarog for "Reflow conditions" /'Taping specifications" and "Floor life level" . Design and specifications are each subject to change without notice. Ask factory for the current technical specifications...

Abrir o catálogo na página 13

Panasonic INDUSTRY Surface Mount Type TPSF series Conductive Polymer Tantalum Solid Capacitors ^ ^ poscApFeatures • Super low ESR (6 mQ max.) • Super low ESL (0.7 nH max.) • Face down terminal type • RoHS compliance, Halogen free Marking Dimensions (not to scale) Rated voltage code Polarity marking(+) Rated capacitance code : Externals of figure are the reference. Characteristics list Rated voltage (V) *1: Ripple current (100 kHz / +45 T) *2: ESR (100 kHz / +20 T) *3: tan 5 (120 Hz / +20 T) *4: After 5 minutes ♦ Please refer to each page in this catarog for "Reflow conditions" /'Taping...

Abrir o catálogo na página 14

Panasonic INDUSTRY Surface Mount Type TPE series B size Conductive Polymer Tantalum Solid Capacitors ♦ poscAp Marking Features • Small size (L 3.5 x W 2.8 x H 1.9 mm) • Low ESR (15 mfi max.) • RoHS compliance, Halogen free * Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately.

Abrir o catálogo na página 15