cad

Tube Cutter
1 / 12Páginas

Excertos do catálogo

Tube Cutter - 1

TUBE MAKE-TO-ORDER PRODUCTS Tube Cutter with Measuring tape built-in Tube Cutter Tubes to Required Length, using Measuring tape. (Measuring tape length: 1m) Double Blade. Rotate it for New Blade Side. and Surely Cut Tube with Tube Guide. ● Safety Lock Function. Tube cutter Insert Ring Tube

Abrir o catálogo na página 1
Tube Cutter - 2

Tube Series ■ Model Code of Tube Cutter (Example) TC-21 Tube Cutter Tube Cutter ■ Model Code of Tube Cutter Blade (Example) TC-C Replacement Blade ■ Operating procedure and Parts names Standard Tube Takeout direction Multi-core Tube Coiling Tube Twin Coiling Tube Fluororesin / Polyamide Tube Clean Room Tube Anti-Spatter Tube Anti-Stalic Tube Tube Binder Tube cutter ① Unlock the safety lock by sliding it to Open side. Measuring tape Mountain-shaped blade ② Place a tube on Tube Guide and cut it. ③ Lock the safety lock by sliding

Abrir o catálogo na página 2
Tube Cutter - 3

Detailed Safety Instructions Before using PISCO products, be sure to read Safety Instructions and Safety Instruction Manual on page 23 to 27 and Common Safety Instructions for Tubes on page 593 to 594. Warning 1. Do not touch the blade to avoid personal injury. 2. Tighten the screws properly after replacing blade. There is a possibility of getting hurt from the fallen blade due to the loosened screws. Caution unlocked unexpectedly by shakings or impacts. 1. Lock the safety lock when Tube Cutter is not in use. Do not carry it in a pocket. Safety lock can be 2. Tube Cutter can be used for...

Abrir o catálogo na página 3
Tube Cutter - 4

Tube Series TC-21 Tube Cutter Built-in measuring tape (1m) CONTROLLER VALVE Tube Cutter Strap hole Mountain-shaped blade 661 ④ Standard Tube Multi-core Tube Coiling Tube Twin Coiling Tube Fluororesin / Polyamide Tube Clean Room Tube Anti-Spatter Tube Anti-Stalic Tube Tube Binder Tube cutter ① Loosen two screws after unlocking the safety lock. ② Take the blade out from the blade groove. ③ Rotate the blade by 180° to use other side of it. ④ Install it into the blade groove by holding the hexagonal hole of the blade. Mountain-shaped blade (Replacement blade model code: TC-C) ⑤ Tighten the...

Abrir o catálogo na página 4
Tube Cutter - 5

Safety Instructions SAFETY Instructions  This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products.  Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

Abrir o catálogo na página 5
Tube Cutter - 6

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper...

Abrir o catálogo na página 6
Tube Cutter - 7

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors....

Abrir o catálogo na página 7
Tube Cutter - 8

http://www.pisco.co.jp http://www.pisco.co.jp 1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NBR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a...

Abrir o catálogo na página 8
Tube Cutter - 9

Safety Instructions 7. Instructions for Tube Disconnection ① Make sure there is no air pressure inside of the tube, before disconnecting it. ② Push the release-ring of the push-in fitting evenly and deeply enough to pull out the tube toward oneself. By insufficient pushing of the releasering, the tube may not be pulled out or damaged by scratch, and tube shavings may remain inside of the fitting, which may cause the leakage later. 8. Instructions for Installing a fitting ① When installing a fitting, use proper tools to tighten a hexagonal-column or an inner hexagonal socket. When inserting...

Abrir o catálogo na página 9
Tube Cutter - 10

Tube Series Common Safety Instructions for Tubes Before selecting or using PISCO products, read the following instructions. Read the detailed instructions for individual series as well as the instructions below. Warning 1. Avoid any load on Tubes such as tensile strength, twisting and bending. These may cause the crush, burst and escape of Tubes. 2. Protect Tubes from scratches caused by snagging or kinking. It may cause the burst of Tubes. 3. The burst pressure of Tubes drops as temperature rises. Read the operating pressure in the catalog well, and apply safety factor. 4. The minimum...

Abrir o catálogo na página 10
Tube Cutter - 11

Caution 1. When bending tubes, observe the minimum bending radius and minimum installation radius. 2. When piping, provide sufficient lengths of tube, considering possible shrinkage. 3. When Tubes are inserted into Push-In Fitting, make sure that cut end surface of Tubes are right angle, without any scratches on the surface and deformations. 4. Note that the effective cross-section area varies by tube length. Refer to Effective Area of Piping in Tube Performance . ■ Minimum Bending Radius & Minimum Mounting Radius   n= Deformation ratio (%). Standard: under 25%   d= Tube O.D.   L= Measured...

Abrir o catálogo na página 11

Todos os catálogos e folhetos técnicos NIHON PISCO CO.

  1. CTB series

    1 Páginas

  2. FUS8 series

    3 Páginas

  3. 31 & 32 Series

    20 Páginas

  4. VP series

    106 Páginas

  5. CHA series

    8 Páginas

  6. Gripper Series

    15 Páginas

  7. SVB Series

    50 Páginas

  8. SVA series

    13 Páginas

  9. SVR series

    31 Páginas

  10. NSB series

    8 Páginas

  11. BV series

    8 Páginas

  12. HV series

    5 Páginas

  13. Plarailchain SC

    15 Páginas

  14. Plarailchain SPO

    12 Páginas

  15. Plarailchain SP

    14 Páginas

  16. HPO

    12 Páginas

  17. HPU

    12 Páginas

  18. PJN series

    15 Páginas

  19. KJNC series

    15 Páginas

  20. SSJS series

    6 Páginas

  21. Stainless SUS316

    13 Páginas

  22. UE series

    12 Páginas

  23. FB series

    1 Páginas

  24. CTA series

    1 Páginas

  25. SFTN series

    2 Páginas

  26. SET series

    1 Páginas

  27. SFT series

    14 Páginas

  28. ULF series

    12 Páginas

  29. UCQ series

    2 Páginas

  30. UQ series

    12 Páginas

  31. NB series

    12 Páginas

  32. NA series

    12 Páginas

  33. UD series

    12 Páginas

  34. UBS series

    12 Páginas

  35. UBT series

    12 Páginas

  36. UC series

    1 Páginas

  37. UB series

    12 Páginas

  38. AK/AS series

    26 Páginas

  39. NK series

    18 Páginas

  40. Brass Series

    30 Páginas

  41. V-0 series

    27 Páginas

  42. EG Series

    27 Páginas

  43. PP Fitting series

    12 Páginas

  44. PP Series

    26 Páginas

  45. AP series

    18 Páginas

  46. SL series

    16 Páginas

  47. P-SUS series

    33 Páginas

  48. NS series

    24 Páginas

  49. SSP series

    8 Páginas

  50. ATS series

    6 Páginas

  51. Air Filter

    20 Páginas

  52. SFU series

    9 Páginas

  53. JP series

    15 Páginas

  54. ET series

    11 Páginas

  55. EQ series

    19 Páginas

  56. CVLU series

    21 Páginas

  57. CV series

    24 Páginas

  58. JN series

    25 Páginas

  59. JSD series

    10 Páginas

  60. JS Low-Flow series

    17 Páginas

  61. JSC series

    13 Páginas

  62. JS series

    30 Páginas

  63. MA series

    16 Páginas

  64. RH series

    16 Páginas

  65. R series

    16 Páginas

  66. PS series

    16 Páginas

  67. L series

    41 Páginas

  68. FUS20

    7 Páginas

  69. GP series

    13 Páginas

  70. VUS12 series

    2 Páginas

  71. VUS21 series

    14 Páginas

  72. VUS8-S series

    22 Páginas

  73. JSD series

    10 Páginas

  74. JK series

    10 Páginas

  75. RVFUP series

    6 Páginas

  76. VLF series

    16 Páginas

  77. VFL series

    8 Páginas

  78. VF series

    22 Páginas

  79. ECV series

    8 Páginas

  80. VPKE series

    4 Páginas

  81. RPV06 Series

    8 Páginas

  82. VZ Series

    34 Páginas

  83. VX Series

    42 Páginas

  84. VQ Series

    4 Páginas

  85. VN Series

    40 Páginas

  86. VK series

    53 Páginas

  87. VJ Series

    34 Páginas

  88. VG series

    21 Páginas

  89. VRL series

    17 Páginas

  90. VVV series

    11 Páginas

  91. VLS series

    4 Páginas

  92. VM | VC series

    28 Páginas

  93. VY series

    24 Páginas

  94. VB series

    11 Páginas

  95. VH | VS series

    28 Páginas

  96. VPHMP series

    12 Páginas

  97. VYR series

    5 Páginas

  98. HS series

    13 Páginas

  99. HML series

    14 Páginas

  100. VRG series

    18 Páginas

  101. Dry Unit Series

    33 Páginas

  102. VLM series

    12 Páginas

  103. VSPE series

    5 Páginas

  104. VT series

    21 Páginas

  105. PB series

    13 Páginas

  106. JSG series

    17 Páginas

  107. pararel

    3 Páginas

  108. fitting

    4 Páginas

  109. BJSU series

    4 Páginas

  110. SC

    15 Páginas

  111. SPO

    12 Páginas

  112. SP

    13 Páginas

  113. RPV pump

    8 Páginas

  114. Pre-set

    6 Páginas

  115. Flange

    13 Páginas

  116. HML

    14 Páginas

  117. VYR

    5 Páginas

  118. VPLFC

    17 Páginas

  119. SVB

    172 Páginas

  120. SVR

    39 Páginas

  121. 8mm Sensor

    22 Páginas

  122. Vacuum Filter

    28 Páginas

  123. Fall Prevention

    18 Páginas

  124. Vacuum Pen

    21 Páginas

  125. Push-Rod Release

    4 Páginas

  126. cylinder

    22 Páginas

  127. FDAbellows

    6 Páginas

  128. Oval

    80 Páginas

  129. sponge

    50 Páginas

  130. mark-free

    34 Páginas

  131. flat

    42 Páginas

  132. Ultrathin

    34 Páginas

  133. packaging bag

    13 Páginas

  134. multi-bellow

    46 Páginas

  135. bellows pad

    74 Páginas

  136. Skid proof pad

    42 Páginas

  137. soft bellow pad

    60 Páginas

  138. soft pad

    66 Páginas

  139. VRL

    17 Páginas

  140. VZ

    34 Páginas

  141. VX

    42 Páginas

  142. VVV

    11 Páginas

  143. VQ

    42 Páginas

  144. VN

    40 Páginas

  145. VLS

    4 Páginas

  146. VLM

    12 Páginas

  147. VK

    53 Páginas

  148. VJ

    34 Páginas

  149. VG

    21 Páginas

  150. Vacuum Tube

    12 Páginas

  151. Twin Coiling

    12 Páginas

  152. Polyurethane Tube

    12 Páginas

  153. Nylon Tube Series

    12 Páginas

  154. Insert Ring

    12 Páginas

  155. UL series

    12 Páginas

  156. Anti-spatter Tube

    12 Páginas

  157. K series

    30 Páginas

  158. Main Block Series

    24 Páginas

  159. Connector Series

    16 Páginas

  160. Color Cap

    12 Páginas

  161. Vacduum gripper

    18 Páginas

  162. SSNC series

    13 Páginas

  163. SJSC series

    24 Páginas

  164. KJSC series

    17 Páginas

  165. Silencer Series

    13 Páginas

  166. Check Valve

    4 Páginas

  167. Parallel Gripper

    6 Páginas

  168. JSG

    17 Páginas

  169. GENERAL

    106 Páginas

  170. Ball Valve Series

    19 Páginas

  171. Hand Valve Series

    15 Páginas

  172. Change Valve

    11 Páginas

  173. SVA21 Series

    21 Páginas

  174. P Series

    71 Páginas

  175. SVA20 Series

    43 Páginas

  176. RegulatorPL031821m

    12 Páginas

  177. BJSU series

    6 Páginas

  178. NP68-01e

    17 Páginas