NB series
1 / 12Páginas

Excertos do catálogo

TUBE MAKE-TO-ORDER PRODUCTS Tube for General Pneumatic Piping Nylon Tube Series ● Fine Pressure, Wear, and Cold Resistance. Tube for Hot Water and Thermal Oil. 608 Standard Tube Multi-core Tube Coiling Tube Twin Coiling Tube Fluororesin / Polyamide Tube Bending Fatigue Resistance. Stably Usable for Long Time. Color Selections for NB Tube. 9 Color Selections for NA Tube. ● Marking Cutting mark Anti-Spatter Tube Anti-Stalic Tube Tube Binder Tube cutter Cutting mark Clean Room Tube Cutting mark Length Tube is available. (Make-to-Order) Insert Ring

Abrir o catálogo na página 1

Tube Series ■ Model Designation (Example) NA Nylon Tube Series 　NA : Nylon Tube 　NB : Soft Nylon Tube ② Tube dia. (O.D. x I.D.) mm size ※ There is no inch size selection for NB Tube as a standard item. ③ Tube length Code ※ NA1613 (5/8) and NB1613 are available only with 20m length. ④ Tube color code N mm size A inch size Clear blue Milky white Brown Yellow green ※ Standard colors for inch sized NA Tube 1/8, 3/16, 1/4, 3/8 and 1/2 are Black and Milky white. ※ Standard colors for NB1613 are Black, Blue and Milky white. Other colors are available as a make-to-order product. ※ Color selection...

Abrir o catálogo na página 2

■ Specifications Tube type Fluid medium Max. operating pressure (at 20℃ 65%RH) Max. vacuum Operating temp. range Warning ※ 1. Surge pressure must be controlled lower than max. operating pressure when using water (and thermal oil for NB Tube) as a fluid medium. ※ 2. Tap water can be used. Consult with PISCO for using other kind of water. ※ 3. Be sure to place Insert Ring into the tube edge when Tube is inserted into Push-In Fittings with water (and thermal oil for NB Tube) as a fluid medium. ※ 4. The value of max. operating pressure is measured at 20℃ and 65%RH. When Tubes are used in...

Abrir o catálogo na página 3

Tube Series Nylon Tube Series NA Nylon Tube Model code Min. Bending Min. Installation Radius Radius (mm) (mm) O YB Y G Orange Ocher Yellow Green ※ . Left □ in model code : Replace with Tube length ※ . Right □ in model code: Replaced with Tube color code Soft Nylon Tube compliant Standard Tube Min. Bending Min. Installation Radius Radius (mm) (mm) YG CB W B R O YB Y G Bu BR P Black Red Orange Ocher Yellow Green Blue Clear Milky Brown Yellow Pink green blue white Model code

Abrir o catálogo na página 4

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

Abrir o catálogo na página 5

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper...

Abrir o catálogo na página 6

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors....

Abrir o catálogo na página 7

http://www.pisco.co.jp http://www.pisco.co.jp 1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NBR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a...

Abrir o catálogo na página 8

Safety Instructions 7. Instructions for Tube Disconnection ① Make sure there is no air pressure inside of the tube, before disconnecting it. ② Push the release-ring of the push-in fitting evenly and deeply enough to pull out the tube toward oneself. By insufficient pushing of the releasering, the tube may not be pulled out or damaged by scratch, and tube shavings may remain inside of the fitting, which may cause the leakage later. 8. Instructions for Installing a fitting ① When installing a fitting, use proper tools to tighten a hexagonal-column or an inner hexagonal socket. When inserting...

Abrir o catálogo na página 9

Tube Series Common Safety Instructions for Tubes Before selecting or using PISCO products, read the following instructions. Read the detailed instructions for individual series as well as the instructions below. Warning 1. Avoid any load on Tubes such as tensile strength, twisting and bending. These may cause the crush, burst and escape of Tubes. 2. Protect Tubes from scratches caused by snagging or kinking. It may cause the burst of Tubes. 3. The burst pressure of Tubes drops as temperature rises. Read the operating pressure in the catalog well, and apply safety factor. 4. The minimum...

Abrir o catálogo na página 10

Caution 1. When bending tubes, observe the minimum bending radius and minimum installation radius. 2. When piping, provide sufficient lengths of tube, considering possible shrinkage. 3. When Tubes are inserted into Push-In Fitting, make sure that cut end surface of Tubes are right angle, without any scratches on the surface and deformations. 4. Note that the effective cross-section area varies by tube length. Refer to Effective Area of Piping in Tube Performance . ■ Minimum Bending Radius & Minimum Mounting Radius n= Deformation ratio (%). Standard: under 25% d= Tube O.D. L= Measured...

Abrir o catálogo na página 11

NB series 1 / 12Páginas

Excertos do catálogo

Todos os catálogos e folhetos técnicos NIHON PISCO CO.

NB series
1 / 12Páginas