ET series
1 / 11Páginas

Excertos do catálogo

CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Exhaust Throttle (Needle) Valve Exhaust Throttle (Needle) Valve ● Exhaust Throttle (Needle) Valve with Silencer. Connectable to Solenoid Valve and Adjust Cylinder Speed. (It is suitable for applications without enough space around cylinder) Solenoid Valve Cylinder Exhaust Valve Series Price than Speed Controller. Fixed orifice Series Pressure Control er Series Pressure Gauge Series Check Valve Series Silencer Ser

Abrir o catálogo na página 1

Controller Series Exhaust Throttle (Needle) Valve ■ Model Designation (Example) ET Exhaust Throttle (Needle) Valve ① Thread size Thread size Metric thread (mm) Taper pipe thread ■ Speciﬁcations Fluid medium Operating pressure range Operating temp. range Speed Controller Series Stainless Series PP Series Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series ■ Construction Symbol Needle (Nickel-plated brass) PP Series Anti-spatter Series Locknut (Aluminum) Metallic body (Nickel-plated brass) Quick Exhaust Valve Series Exhaust Valve Series Taper pipe thread:...

Abrir o catálogo na página 2

Detailed Safety Instructions Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Warning 1. When controlling the speed of actuators, slowly release the air by adjusting the needle Turn needle in the clockwise direction to close, and in the counterclockwise to open. 2. The clogging of silencer element increases exhaust-resistance. There is a possibility from a fully closed state. In case the needle is opened, actuator can move suddenly. Manual” on page 23 to 27 and “Common Safety Instructions for Controllers” on page 367 to 368. that it causes the...

Abrir o catálogo na página 3

Controller Series Exhaust Throttle (Needle) Valve ET Exhaust Throttle (Needle) Valve Metric thread type Weight CAD file name (g) ※ . “L” is a reference value for height dimension after tightening taper thread. 3D 3D CAD data is available at PISCO website. CAD Control flow Flow rate (l/min(ANR)) Exhaust Valve Series Anti-spatter Series Quick Exhaust Valve Series Flow rate (l/min(ANR)) CAD CAD data is available at PISCO website. Stainless Series Control flow Flow rate (l/min(ANR)) Throttle (Needle) Valve Series Control flow Flow rate (l/min(ANR)) Anti-spatter Series Stainless Series Constant...

Abrir o catálogo na página 4

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

Abrir o catálogo na página 5

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper...

Abrir o catálogo na página 6

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors....

Abrir o catálogo na página 7

http://www.pisco.co.jp http://www.pisco.co.jp 1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NBR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a...

Abrir o catálogo na página 8

Safety Instructions 7. Instructions for Tube Disconnection ① Make sure there is no air pressure inside of the tube, before disconnecting it. ② Push the release-ring of the push-in fitting evenly and deeply enough to pull out the tube toward oneself. By insufficient pushing of the releasering, the tube may not be pulled out or damaged by scratch, and tube shavings may remain inside of the fitting, which may cause the leakage later. 8. Instructions for Installing a fitting ① When installing a fitting, use proper tools to tighten a hexagonal-column or an inner hexagonal socket. When inserting...

Abrir o catálogo na página 9

Controller Series Common Safety Instructions for Controllers Before selecting or using PISCO products, read the following instructions. Read the detailed instructions for individual series as well as the instructions below. Warning 1. Some products have an air direction to control. Make sure to distinguish the direction by marking on the products. Installing the product with the wrong direction may cause personal injury or property damage. 2. Avoid any load on PISCO products such as a tensile strength, twisting, bending, dropping and excessive impacts. These may cause damage to the...

Abrir o catálogo na página 10

Thread type Taper pipe thread Unified thread National pipe thread taper Parallel pipe thread 12 14N m 22 24N m 28 30N m After hand tightening 1/2~1 turns Thread type Metric thread Parallel pipe thread Tightening torque 1/6 turns after hand tightening 1/2~1 turns after hand tightening 3. Instructions for removing Controller 　① hen removing controllers, use proper tools to loosen a hexagonal-column or W a knurling. 　② emove the sealant stuck on the mating equipment. The remained sealant R may get into the peripheral equipment and cause malfunctions. 4. Fixed Orifice Joint Series and Speed...

Abrir o catálogo na página 11

ET series 1 / 11Páginas

Excertos do catálogo

Todos os catálogos e folhetos técnicos NIHON PISCO CO.

ET series
1 / 11Páginas