8mm　Sensor
1 / 22Páginas

Excertos do catálogo

VACUUM ACCESSORIES Pressure Switch with Super slim LED Display 8mm width LED Digital Pressure Sensor ● Super slim and light weight pressure sensor with a LED display. width: 8.2mm, height: 34.3mm, length: 62.2mm, weight: 17g Indicator font size on the LED display is 4.5mm high for better visibility. ● All settings are done by 2 push buttons. ● Three mounting options : Bracket, DIN rail or via screws directly. Port selection: Single Port and Inline Port. ● Port type: Female Thread (M5) and Push-In Fitting (ø1.8, 3, 4mm). 8mm LED Pressure Sensor LED Pressure Sensor Small Sensor Pressure Sensor Wi

Abrir o catálogo na página 1

Vacuum Accessories Series VACUUM ACCESSORIES EXTERNAL VACUUM VACUUM CONTROLLER GENERATOR 8mm width LED Digital Pressure Sensor ■ Model Designation (Example) VUS8 8mm width LED Digital Pressure Sensor S ③ Bracket (option) ② Pressure range ① Port type Port type Inline Port code Single Port code Tube O.D.（mm） ② Pressure range Code Pressure range ③ Bracket (option) No code without Bracket Code Bracket (option) ■ Model Designation of Bracket (Example) 797 Small Vacuum Regulator Add-on Blow-off Controller Vacuum Filter Free Holder Fall Prevention Valve 8mm LED Pressure Sensor ※ 2 inner hexagonal...

Abrir o catálogo na página 2

■ Specifications Model code Fluid medium Pressure detection Diffusion type semiconductor pressure switch Operating temp. range General Storage temperature range spec. Operating humidity range Air (non-corrosive air) 0 ~ 50°C (No freezing) Atmospheric pressure / Humidity: 65% RH or less (No freezing) 35 ~ 85%RH (No dew condensation) Vibration resistance Impact resistance Protective structure Current consumption 30mA or less (all LED and no-load of 2 switch outputs: ON) Display element Rated voltage Display frequency Monitoring system Excessive rated pressure: Blinking display Special Panel...

Abrir o catálogo na página 3

Vacuum Accessories Series ■ Using Method ■ Wiring Connection Method (Brown) Load Main circuit ■ Names of the Panel Part VACUUM ACCESSORIES EXTERNAL VACUUM VACUUM CONTROLLER GENERATOR 8mm width LED Digital Pressure Sensor Starting Operation Mode. ■ Operation Procedure of Panel Add-on Blow-off Controller Vacuum Filter Free Holder Fall Prevention Valve 8mm LED Pressure Sensor Panel Lock Small Vacuum Regulator ▲ More than 4 seconds ▼ More than 4 seconds Operation Mode (Pressure Display) ▲＋▼ More than a second Select Mode “dl” Invalid operation for more than 5 seconds Each Setting Mode ▲＋▼ More...

Abrir o catálogo na página 4

■ Operation Procedure of Panel ① Operation Procedure of Select Mode Push both (▼) and (▲) button simultaneously for more than a second in Operation Mode. “dl” is displayed in Select Mode. Display of Select Mode is changed in the order of “dl” , “In” “SS” and “0A” by pushing (▼) button. , VACUUM ACCESSORIES dl: Display Setting Mode In: Initial Setting Mode SS: Switch Setting Mode 0A: Zero Adjusting Mode Select a desired mode and push both (▼) and (▲) button simultaneously for more than a second to- enter each setting mode. Caution 1. isplay automatically returns to Operation Mode if no...

Abrir o catálogo na página 5

Vacuum Accessories Series ③ Setting Procedure of Display Magnification and Switch Output Operation Display Magnification Follow “①Operation Procedure of Select Mode” and enter Initial Setting Mode. Switch Output Operation Current setting is displayed. Left digit shows Display Magnification No. and right digit shows Switch Output Operation No.. VACUUM ACCESSORIES EXTERNAL VACUUM VACUUM CONTROLLER GENERATOR 8mm width LED Digital Pressure Sensor Display Magnification Setting or Switch Output Operation Setting can be selected by (▲) button. Blinking LED shows the setting item. Display...

Abrir o catálogo na página 6

Switch Output Operation No. / Operation Drawing SW1 SW2 Separate Mode Wind Comparator Mode Separate Mode Wind Comparator Mode LO A B HI LO A HI B ○ ○ 1 ○ ○ 2 ○ ○ 3 ○ ○ 4 ○ ○ 5 ○ ○ 6 ○ ○ 7 ○ ○ 8 Pressure setting Setting 1 Lower limit: Setting 1 Setting 2 Lower limit: Setting 1 (Operating point) Upper limit: Setting 2 Upper limit: Setting 2 Output Mode Operation Wind Comparator Mode OFF S: Negative pressure -100kPa SR: Compound pressure -100kPa S: Negative pressure -100kPa SR: Compound pressure -100kPa VACUUM ACCESSORIES Separate Mode P1:SW1 S: Negative pressure -100kPa SR: Compound pressure...

Abrir o catálogo na página 7

Vacuum Accessories Series ④ Setting Procedure of Switch Pressure Value, Hysteresis and Filter Follow “①Operation Procedure of Select Mode” and enter Switch Setting Mode. VACUUM ACCESSORIES Pressure value setting of SW1 Pressure value setting of SW2 Filter setting EXTERNAL VACUUM VACUUM CONTROLLER GENERATOR 8mm width LED Digital Pressure Sensor Hysteresis setting S1 LED flashes and a current pressure value is displayed. “Pressure value setting of SW1” , “Pressure value setting of SW2” “Hysteresis setting” and “Filter setting” are displayed in order by , pushing both (▼) and (▲) buttons...

Abrir o catálogo na página 8

⑥ Setting Procedure of Panel Lock Setting of Panel Lock Press (▲) button for more than 4 seconds in Operation Mode. “PL” on the display flashes 3 times and Panel Lock will be set. The pressure display come back again after the setting. Unsetting of Panel Lock VACUUM ACCESSORIES Press (▼) button for more than 4 seconds in Operation Mode. “PA” on the display flashes 3 times and Panel Lock will be unset. The pressure display comes back again after unsetting. Operation during Panel Lock If any button operation is done during Panel Lock, “PL” on the display flashes 3 times and the pressure value...

Abrir o catálogo na página 9

Vacuum Accessories Series ■ How to insert and disconnect 1. How to insert and disconnect tubes ① Tube insertion Insert a tube into Push-In Fitting up to the tube end. Lock-claws bite the tube and ﬁx it automatically, then the elastic sleeve seals around the tube. Refer to “2. Instructions for Tube Insertion” under “Common Safety Instructions for Fittings”. ※ . When a tube is insterted / disconnected while the sensor is mounted on DIN rail, hold and ﬁx the sensor by hand in order to avoid a load on Release Latch. Release Latch ② Tube disconnection The tube is disconnected by pushing...

Abrir o catálogo na página 10

8mm Sensor 1 / 22Páginas

Excertos do catálogo

Todos os catálogos e folhetos técnicos NIHON PISCO CO.

8mm　Sensor
1 / 22Páginas