Lifting Points shanks, lifter studs, eyebolts, clamping claws, screws and bolts
1 / 20Páginas

Lifting Points

2131.30. ■EFIBRO Description: Only tighten eyebolts hand-tight. Not suitable for diagonal pull. Avoid turning movements during transport. Material: Alloyed steel, hardened and tempered, quality class 8 Note: Load capacity according to operating instructions or load capacity table in the specified directions of pull. When selecting the arrangement, make sure that unequal loading does not occur, e.g. if: - no free adjustment is possible in the direction of pull - direction of pull does not lie in the specified range Safety factory 4 2131.30. Lifting eye bolt, high tensile Rated carrying Order...

Attachment point screwable profilift gamma Description: When replacing, make sure the Allen screw is seated firmly. Adjustable in the direction of force, thus no unintended opening up and overtwisting! Screwing in and out by hand possible. The ring must be able to be turned 360° in the screwed tight state. Material: Structural parts: High-strength chrome nickle alloyed Q & T steel. Screws: High-strength screws strength class 10.9, 100 % crack tested Note: Ensure even screw-in surface, threads must be screwed in completely. Each attachment point is provided with an individual serial...

2131.32. ■EFIBRO Description: Pay attention to firm seating of the ring nut when inserting. Adjustable in the direction of force, thus no unintended opening up and overtwisting! Screwing in and out by hand possible. The ring must be able to be turned 360° in the screwed tight state. Material: Structural parts: High-strength chrome nickle alloyed Q & T steel. Nuts: High-strength nuts, strength class 10, 100 % crack tested Note: Ensure even screw-in surface, threads must be screwed in completely. Each attachment point is provided with an individual serial number Information about installation...

Hoisting snap link, omnidirectional 2131.33. If ill Description: The hinged unit is free to rotate through 360°, self-align with the direction of pull and folding. The hoisting Snap Link must be installed in the stress direction before loading, must be able to move freely and may not be supported at an angle. Do not rotate under load. Full load bearing capacity in any direction. Complete with a 100% crack-checked outer and inner hexagonal bolt for universal tool use. Material: Alloyed tool steel Note: Ensure even screw-in surface, threads must be screwed in completely. 2131.33. Hoisting...

■EFIBRO Description: For loads which are turned and flipped. Ball-bearing-mounted - under load turnable by 360° Not suitable for continuous turning movements under full load. Material: Structural parts: High-strength chrome nickle alloyed Q & T steel. Screws: High-strength screws strength class 12.9, 100 % crack tested Note: Ensure even screw-in surface, threads must be screwed in completely. The threaded connection on the transport belt must be suitable for the force transmission. Each attachment point is provided with an individual serial number Information about installation and removal,...

Triple vortice ring Description: The triple vortice rings with double bearing mount for smooth tipping, turning and flipping. Also turnable 90° for screw-in direction under full load. Not suitable for continuous turning movement under full load. The optimised design prevents damage to lifting tackle and the valuable load when turning. For ring assembly, round slings, wire ropes, hook assemblies, etc. Material: High-strength chrome-nickle alloyed Q & T steel, Screws: high-strength screws, min. strength category 10.9, 100 % crack inspected Note: Ensure even screw-in surface, threads must be...

2131.36. ■EFIBRO Description: The double vortice rings with double bearing mount for smooth tipping, turning and flipping. Also turnable 90° for screw-in direction under full load. Not suitable for continuous turning movement under full load. The optimised design prevents damage to lifting tackle and the valuable load when turning. For ring assembly, round slings, wire ropes, hook assemblies, etc. Material: High-strength chrome-nickle alloyed Q & T steel, Screws: high-strength screws, min. strength category 10.9, 100 % crack inspected Note: Ensure even screw-in surface, threads must be...

Double vortice ring Description: The double vortex ring was especially designed to guarantee lifting under rotation. Its double joint permits a perfect alignment for load suspension. Material: High-strength chrome-nickle alloyed Q & T steel, Screws: high-strength screws, min. strength category 10.9, 100 % crack inspected Note: Ensure even screw-in surface, threads must be screwed in completely. The threaded connection on the transport belt must be suitable for the force transmission. Each attachment point is provided with an individual serial number Information about installation and...

PiFIBRO Description: The double vortex ring with centring device was especially designed to guarantee lifting under rotation. The centring device increases the resistance of the axis in case of lateral mounting. Material: High-strength chrome-nickle alloyed Q & T steel, Screws: high-strength screws, min. strength category 10.9, 100 % crack inspected Note: Ensure even screw-in surface, threads must be screwed in completely. The threaded connection on the transport belt must be suitable for the force transmission. Each attachment point is provided with an individual serial number Information...

Double vortice ring with internal thread 2131.39. Description: The double vortex ring with internal thread was especially designed to guarantee lifting under rotation. Its double joint permits a perfect alignment for load suspension. Material: High-strength chrome-nickle alloyed Q & T steel Note: Ensure even screw-in surface, threads must be screwed in completely. The threaded connection on the transport belt must be suitable for the force transmission. Each attachment point is provided with an individual serial number Information about installation and removal, see operating...