Catálogos >
Brevini Power Transmission >
VPS Mobile Valves

VPS Mobile Valves
1 / 68Páginas

Excertos do catálogo

Motion Systems Technical Catalogue

© 2018 Dana Brevini S.p.A. all rights reserved. Hydr-App, SAM Hydraulik, Aron, Brevini Hydraulics, BPE Electronics, VPS Brevini, OT Oiltechnology, logos are trademarks or are registered trademarks of Dana Brevini S.p.A. or other companies Dana in Italy and other countries. The technical features supplied in this catalogue are non binding and no legal action can be taken against such material. Dana Brevini will not be held responsible for information and speciﬁcations which may lead to error or incorrect interpretations. Given the continuous technical research aimed at improved technical...

Abrir o catálogo na página 3

Motion Systems INTRODUCTION OIL VISCOSITY ACCORDING TO TEMPERATURE Read this instructions carefully before installation. All operations must be carried out by qualified personnel following the instructions. The user must periodically inspect, based on the conditions of use and the substances used, the presence of corrosion, dirt, the state of wear and correct function of the valves. HYDRAULIC FLUID Use only mineral oil (HL, HLP) according to DIN 51524. Use of other different fluids may damage the good operation of the valve. VISCOSITY The oil viscosity must be in the range of 10 mm2/s to...

Abrir o catálogo na página 4

Motion Systems Table 2: Reccomanded contamination level.

Abrir o catálogo na página 5

Motion Systems MAIN CHARACTERISTICS GENERAL CONDITION OF WORK All the production Dana Brevini want to be a high quality production. Infact the project of each single valve and the choice of the better materials, machined with the highest tecnologies and under the strongest controls in each process, allow highest characteristics and numerous applications described in the following pages. Furthermore: (!) threads availables on request (2) threads availables on requestsolo only for outlet side (3) inlet section with top output (4) output section with standard upper thread + carry over...

Abrir o catálogo na página 6

Motion Systems OVERALL DIMENSIONS MONOBLOCK Type

Abrir o catálogo na página 7

CHARACTERISTIC PRESSURE DROP FLOW CURVES Inlet pressure drop between P spool in central position Inlet pressure drop between P A (B) spool in working position N.o sections Inlet pressure drop between A (B) spool in working position Metering curves are different for each typee of spool. Therefore particular curves are supplied on request The curves are obtained using standard double acting spool (cod. ST1) with oil at 50°C and viscosity 36 mm² / s 6

Abrir o catálogo na página 8

Motion Systems OVERALL DIMENSIONS MONOBLOCK Type

Abrir o catálogo na página 9

CHARACTERISTIC PRESSURE DROP FLOW CURVES Inlet pressure drop between P spool in central position Inlet pressure drop between P A (B) spool in working position psi bar 24 Inlet pressure drop between A (B) spool in working position Metering curves are different for each typee of spool. Therefore particular curves are supplied on request The curves are obtained using standard double acting spool (cod. ST1) with oil at 50°C and viscosity 36 mm² / s 8

Abrir o catálogo na página 10

Ordering code Inlet section Outlet section Working sections (repeat for any section) N.o working sections Inlet type Valves arrangement Main relief valve setting Positioning / Control side B Service port valves Overload valve setting Hand lever Working section repeated for n. times (1) Optional ﬁelds. Not specify if not required. (2) Service port valves optional, is required a special monoblock body. HYDRAULIC SCHEME Working sections Inlet section Outlet section Side B (Positioning / Control) Outlet section

Abrir o catálogo na página 11

Ordering code ^ Motion Systems ORDERING CODE EXAMPLE 004 - Direct main relief valve + Solenoid dump valve 24V N. Open CS1 - Spool control side A D4 - Spool control side B, 3 pos. spring centred spool, detent in "b" VB1(150) - Overload valve in position "B" - Setting 150 bar W2 - Standard handle lever X2 - Working section repeated for n. 2 times ST1 - Spool, 3 position, double acting CS1 - Spool control side A D4 - Spool control cap side, 3 pos. spring centred spool, detent in "b" W2 - Standard handle lever

Abrir o catálogo na página 12

Motion Systems (1) On request. RIGHT inlet section with top inlet (IDT). Contact our sales department. (2) On request. RIGHT inlet section with side inlet (IDL). Contact our sales department.

Abrir o catálogo na página 13

Motion Systems Valves choice MONOBLOCK -'] Valves arrangements and main - relief valve setting DCV40 (!) Specify pressure relief valve setting (from 20 to 400 bar). In the order it is suggested specify the flow rate. (2) Include block (DCV40 ) and special monoblock body

Abrir o catálogo na página 14

Motion Systems 3 position, double acting 3 positions, single acting in A - A open 3 positions, double acting, - Lc blocked - A and B open 3 positions, single acting in B - B open 3 positions, double acting, - Lc blocked - A and B blocked 3 positions, double acting regenerative in A (not standard) 3 positions, double acting, - A and B open 3 positions, double acting regenerative in B (not standard) 3 positions, double acting, - A open - B blocked 4 positions, double acting with 4th float position 3 positions, double acting, - A blocked - B open 2 positions with function dead man...

Abrir o catálogo na página 15

Spool control side A BREVINI Motion Systems CS** Spool control side A Description Standard handle (1) CSA. = Aluminium version (only DCV40)

Abrir o catálogo na página 16

Motion Systems | CS** | Spool control side A Description Drawing Safety handle locked in neutral position Safety handle locked in position "a” MONOBLOCK Security handle locked in position "b” Security handle locked in position "a” and "b” Security handle locked in 4th position Any positions detented lever (1) CSA. = Aluminium version (only DCV40)

Abrir o catálogo na página 17

Motion Systems | CS** | Spool control side A Description Drawing Cloche control with fulcrum on upstream section Cloche control with fulcrum on downstream section Cloche control with fulcrum turned 180° on the downstream section Cloche control with fulcrum turned 180° on the upstream section (1) (CX) code required to use on 2th section (2) Cable supplied on request. Lenght cable and control, contact our commercial dept

Abrir o catálogo na página 18