Catálogos >
Angst+Pfister Sensors and Power AG >
STX Series – Model 13A

STX Series – Model 13A
1 / 11Páginas

Excertos do catálogo

ANALOG OUTPUT Solid State Pressure Sensor STX Series - Model 13A FEATURES • Fastening Mount • Calibrated Span and Offset • Multi-order Temperature compensation • 0.5V/4.5V or optional • 3V or 5V Supply • Customized Configuration upon request DESCRIPTION The Series STX Model 13A is a smart pressure sensor with calibrated and amplified output. The ceramic hybrid package performs excellent isolation to external stress during operation. Digital compensation of sensor offset, sensitivity, temperature drift and nonlinearity is accomplished in factory via an internal DSP running a correction algorithm with calibration coefficients stored in on-chip EEPROM. A variety of output configuration, including resolution, sampling rate, output interface are available to provide simple and ready-to-use solution for a wide rage of application. The Series STX 13A is available for pressure range from 0.15 psi to 100 psi. Please contact factory for detail. Competitive sensor & power supply solutions worldwide PEWATRON

Abrir o catálogo na página 1

XXX G - X 0 X X Option 10: No special reguest 97: Compensated Temp 0~85 degC Other options available upon request. Series Supply Voltage Blank = 4.75 to 5.25 V L = 2.75 to 3.33 V Type of Pressure G: Gage (Port B only) H: Gage (Dual Port) A: Absolute (Port A only) D: Differential (Dual Port) Leading Direction 0= same side Notes: Custom ranges and units are available upon request. Please contact factory. 1. Specifying differential pressure means a ± pressure range. 2. Differential pressure can be specified to a maximum of +/- 100 psi. 3. Custom output, pressure range and temperature...

Abrir o catálogo na página 2

Unless otherwise specified, all parameters are measured at 3/5V, 25 °C and 60% RH NOTES: N.C. pins must be left floating A 0.1 uf capacitor must be connected between Vdd and Vss * Pin out configuration may vary, refer to individual data sheet Soldering reflow: 250 °C for 5 sec max. Competitive sensor & power supply solutions worldwide

Abrir o catálogo na página 3

1. Supply 3V or 5V must be ordered separately. 5. Over-pressure will vary on different range 2. Smaller range and other units are also available for ordering 6. Wetted material: PA, RTV, Epoxy, ceramic, Au, nickel and silicon 3. Accuracy includes NOL, hysterisis, TCS and TCO over 0/50°C, BFSL definition 7. Output is ratiometric to supply voltage 4. For differential, offset = 2.50V, Span = ±2.00V 8. Output load resistance to Vss or Vdd: 2.5KQ (min), 10KQ (typ) 9. Zeroing at installation is required NOTE: 1. Port B is used for positive differential 2....

Abrir o catálogo na página 4

Unless otherwise specified, all parameters are measured at 3/5V, 25 °C and 60% RH 1. Supply 3V or 5V must be ordered separately. 5. Wetted material: PA, RTV, Epoxy, ceramic, Au, nickel and silicon 2. Smaller range and other units are also available for ordering 6. Output is ratiometric to supply voltage 3. Accuracy includes NOL, hysterisis, TCS and TCO over 0/50°C, BFSL definition 7. Output load resistance to Vss or Vdd: 2.5KQ (min), 10KQ (typ) 4. For differential, offset = 2.50V, Span = ±2.00V Bottom View NOTE: 1. Port B is used for positive differential 2. Port A is used for...

Abrir o catálogo na página 5

DIGITAL OUTPUT Solid State Pressure Sensor STX Series - Model 13D FEATURES • Fastening Mount • Calibrated Span and Offset • Multi-order Temperature compensation • OWI, I2C or SPI Interface • 3V or 5V Supply • Customized Configuration upon request DESCRIPTION The Series CCD Model 13D is a smart pressure transducer with digital output via 1-wire serial, I2C or SPI interface. Digital compensation of sensor offset, sensitivity, temperature drift and nonlinearity is accomplished in factory via an internal DSP running a correction algorithm with calibration coefficients stored in on-chip...

Abrir o catálogo na página 6

XXX G - X 0 X XOption 0: No special reguest Supply Voltage Blank = 4.75 to 5.25 V L = 2.75 to 3.33 V Type of Pressure G: Gage (Port B only) H: Gage (Dual Port) A: Absolute (Port A only) D: Differential (Dual Port) Leading Direction 0= same side Notes: Custom ranges and units are available upon request. Please contact factory. 1. Specifying differential pressure means a ± pressure range. 2. Differential pressure can be specified to a maximum of +/- 100 psi. 3. Custom output, pressure range and temperature compensated range are available. 4. Negative gage normally has offset (0.5V) at 0 psi...

Abrir o catálogo na página 7

Unless otherwise specified, all parameters are measured at 3/5V, 25 °C and 60% RH NOTES: N.C. pins must be left floating A 0.1uf capacitor must be connected between VDD and Vss * Pin out configuration may vary, refer to individual data sheet Soldering reflow: 250 °C for 5 sec max. Competitive sensor & power supply solutions worldwide

Abrir o catálogo na página 8

1. Supply 3V or 5V must be ordered separately. 5. Over-pressure will vary on different range 2. Smaller range and other units are also available for ordering 6. Wetted material: PA, RTV, Epoxy, ceramic, Au, nickel and silicon 3. Accuracy includes NOL, hysterisis, TCS and TCO over 0/50°C, BFSL definition 7. Output load resistance to Vss or Vdd: 2.5KQ (min), 10KQ (typ) 4. For differential pressure, offset = 2000 hex, FS = 666/3999 8. Zeroing at installation is required NOTE: 1. Port B is used for positive differential 2. Port A is used for absolute 3. Port B...

Abrir o catálogo na página 9

Unless otherwise specified, all parameters are measured at 3/5V, 25 °C and 60% RH Parameters NOTES: 1. Supply 3V or 5V must be ordered separately. 5. Minimum pull-up on SDA and SCL is 1KQ 2. Smaller range and other units are also available for ordering 6. 1X for 100 3. Accuracy includes NOL, hysterisis, TCS and TCO over 0/50°C, BFSL definition 7. The factory setting for I2C slave address is 0x28 4. For differential pressure, offset = 2000 hex, FS = 666/3999 8. Wetted material: PA, RTV, Epoxy, ceramic, Au, nickel and silicon Dimension Port A NOTE: 1. Port...

Abrir o catálogo na página 10

Office Germany: Pewatron Deutschland GmbH EdisonstraEe 16 D-85716 UnterschleiEheim Phone +49 89 374 288 87-0 info.de@pewatron.com PEWATRON 5ENS0R5 • POWER SOLUTIONS Geometrical sensors Sensor elements Thorsten Ravagni Phone +49 60 479 53 627 thorsten.ravagni@pewatron.com Sales Other Countries / Product Management Pressure Sensors Gas sensors / Gas sensor modules Load cells Dr. Thomas Clausen Phone + 41 44 877 35 13 thomas.clausen@pewatron.com Flow / Level / Medical products Linear position sensors Angle sensors Eric Letsch Phone + 41 44 877 35 14 eric.letsch@pewatron.com Accelerometers /...

Abrir o catálogo na página 11