Catálogos >
ABB Measurement & Analytics >
TEIP11 I/P signal converter for standard signals

TEIP11 I/P signal converter for standard signals
1 / 16Páginas

Excertos do catálogo

TEIP11 I/P signal converter for standard signals - 1

ABB MEASUREMENT & ANALYTICS | DATA SHEET TEIP11 I/P signal converter for standard signals

TEIP11 I/P signal converter for standard signals - 2

TEIP11 I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-EN REV. D — Flow in air pressure — Proven and reliable concept — Integral mount design • Small dimensions, low weight — Sturdy construction and solid functionality • Influence of shock and vibration < 1 % bei 10 g — Variety of signal ranges • Input e.g. 0 to 20 mA or 4 to 20 mA • Output 0.2 to 1 bar (3 to 15 psi) — Wide temperature range • From –40°(optional –55°) to 85° C (–40° [optional 67°] to 185°F) — Approvals for explosion protection • ATEX, FM / CSA, GOST for intrinsically s

Abrir o catálogo na página 2

TEIP11 I/P signal converter for standard signals - 3

TEIP11 I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-EN REV. D Change from one to two columns — Concept The TEIP11 signal converter converts standard electrical signals, e.g. 4 to 20 mA to 0.2 to 1 bar (3 to 15 psi). It is therefore a connecting link between electrical/electronic and pneumatic systems. The signal conversion process is similar to the patented force balance method. Special features of the TEIP11 signal converter are its relatively small dimensions and outstanding operational stability when subject to shock and vibration. The converter can be subjected to loads up to...

Abrir o catálogo na página 3

TEIP11 I/P signal converter for standard signals - 4

TEIP11 I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-EN REV. D Transmission data and contributing factors Characteristic curve Linear, direct, or reverse action Characteristic curve deviation < 1 % Specification Input (electric) Signal range 0 to 20 mA or 4 to 20 mA 0 to 10 mA or 10 to 20 mA 4 to 12 mA or 12 to 20 mA (additional ranges available upon request) Overpressure limit Dead band 30 mA (for Ex devices see Ex relevant specifications on < 0.1 % Capacitance / inductance Negligible Output (pneumatic) Signal range 0.2 to 1 bar (3 to 15 psi) Air capacity Temperature < 1 % /...

Abrir o catálogo na página 4

TEIP11 I/P signal converter for standard signals - 5

TEIP11 I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-EN REV. D Operating conditions at installation site Ambient temperature Depending on the ordered model: -40 to 85 °C (-40 to 185 °F) -55 to 85 °C (-67 to 185 °F) For Ex d: -40 to 85 °C (-40 to 185 °F) Mounting position Any Environmental capabilities Climate class GPF or FPF acc. to DIN 40040 Temperature: -55 to 85 °C (-67 to 185 °F), -45 to 85 °C (-49 to 185 °F) Relative humidity for operation, storage, or transport: 75 % average, 95 % short-term, no condensation Design for rail mounting Material / IP rating IP 20 aluminum housing...

Abrir o catálogo na página 5

TEIP11 I/P signal converter for standard signals - 6

TEIP11 I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-EN REV. D ... Specification Accessories ‘Ex d’ cable gland Brass, with M20 x 1.5 thread Stainless steel mounting bracket for wall mounting or 2 in pipe mounting For aluminum or stainless steel field housing unit Material for block mounting Connection block for 4 signal converters, End panel with central supply air connection % NPT, dummy panel Type Examination Test Certificate DMT 02 ATEX E 121 X Device class II 2G (General requirements) EN 60079-1: 2007 (Flameproof enclosure ‘d’) System bus, computer interfaces Current <...

Abrir o catálogo na página 6

TEIP11 I/P signal converter for standard signals - 7

TEIP11 I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-EN REV. D Marking II 2G Ex ia IIC T6 resp. T4 Gb Type Examination Test TUV 99 ATEX 1487 X Temperature classes for the following versions: TEIP11 Doc. 901068-SMD and TEIP11-PS Doc. 901068-SMD and TEIP11-PS Doc. 901069-SMD FM / CSA oIntrinsically safe FM FM ‘intrinsically safe' (not for metal field housing units) I.S.: CL I/Div 1/Grp A B C D FM ‘intrinsically safe' (only for metal field housing units) I.S.: CL I-II-II/Div 1/Grp A B C D E F G S.: CL II/Div 2/Grp G S.: CL III/Div 2 Non-incendive FM N.I.: CL I/Div 2/Grp A B C D...

Abrir o catálogo na página 7

TEIP11 I/P signal converter for standard signals - 8

TEIP11 I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-EN REV. D — Dimensions Design for control room housing unit for rail mounting Dimensions in mm (in) 5 Mounting bracket for DIN rail mounting 3 Output Figure 2: Dimensions of control room housing design for rail mounting

Abrir o catálogo na página 8

TEIP11 I/P signal converter for standard signals - 9

TEIP11 I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-EN REV. D Design for aluminum or stainless steel field mount housing For wall mounting or pipe mounting Dimensions in mm (in) 3 Supply air Figure 3: Dimensions of field mount housing for wall or pipe mounting

Abrir o catálogo na página 9

TEIP11 I/P signal converter for standard signals - 10

TEIP11 I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-EN REV. D — … Dimensions Mounting module for OEM applications Dimensions in mm (in) Figure 4: Dimensions of mounting module for OEM application

Abrir o catálogo na página 10

TEIP11 I/P signal converter for standard signals - 11

TEIP11 I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-EN REV. D Ordering InformationMain ordering information TEIP11 TEIP11 I/P Converter, signal converter for standard signals, without power stage V18312H X Explosion Protection Standard (without explosion protection) 1 FM / CSA Intrinsically Safe and Explosion-proof 6* GOST Russia - Ex ia A** GOST Russia - Ex d D** Design Control room housing IP 20, for rail mounting Aluminium field housing, IP 65, for wall or pipe mounting Aluminium field housing, IP 65, add-on module for OEM applications Stainless steel field housing,...

Abrir o catálogo na página 11

TEIP11 I/P signal converter for standard signals - 12

TEIP11 I/P SIGNAL CONVERTER FOR STANDARD SIGNALS | DS/TEIP11-EN REV. D ... Ordering Information Additional ordering information TEIP11 TEIP11 I/P-Umformer, Signalumformer fur Normsignale, ohne Leistungsstufe XXX XXX Certificate of Compliance Certificate of compliance with the order acc. EN 10204-2.1 (DIN 50049-2.1) with item description CF2 Inspection Certificate Inspection certificate 3.1 acc. EN 10204 CBA Accessories Order code TEIP11 Cable gland EEx d, brass, M 20 x 1.5 thread 319343 TEIP11 Mounting bracket, stainless steel, for wall mounting 319344 TEIP11 Mounting...

Abrir o catálogo na página 12