Catálogos >
ABB Measurement & Analytics >
PME120-AI / PME120-AN (Contrac)

PME120-AI / PME120-AN (Contrac)
1 / 28Páginas

Excertos do catálogo

PME120-AI / PME120-AN (Contrac) Electrical rotary actuator

PME120-AI / PME120-AN (CONTRAC) ELECTRICAL ROTARY ACTUATOR | DS/PME120-EN REV. D — For continuous control mode, nominal torque 100 Nm (80 lbf-ft), with integrated electronic unit or for separate electronic unit. — Process optimization thanks to maximum control precision — Maintenance-free up to 10 years — Electrical actuator for continuous positioning, three-point position control, or bus control — Stall-proof without the need for position- or torque-dependent shut-off — Adjustable mechanical limit stops for defined operating range — Handwheel for emergency operation — Control only via...

Abrir o catálogo na página 2

PME120-AI / PME120-AN (CONTRAC) ELECTRICAL ROTARY ACTUATOR | DS/PME120-EN REV. D Change from one to two columns — Brief description Compact actuator for the operation of final control elements with rotary movement such as valve flaps, ball valves, etc. The torque is transferred via a lever-type actuator or the actuator is directly coupled to the shaft of the final control element. The actuator is controlled using a Contrac electronic unit. This electronic unit serves as the interface between the actuator and the control system. During continuous positioning, the electronic unit varies the...

Abrir o catálogo na página 3

PME120-AI / PME120-AN (CONTRAC) ELECTRICAL ROTARY ACTUATOR | DS/PME120-EN REV. D — … Brief description The handwheel offers an optimum level of performance between handwheel forces and rotational speed, owing to the design principle of the differential gearing. Furthermore, the gear train is not interrupted, even though it is possible to adjust the handwheel at any time. This ensures maximum operational reliability. The 3-phase asynchronous motor is equipped with a spring-loaded brake. The brake is energized in automatic mode. In the case of a fault or failure of the supply voltage, the...

Abrir o catálogo na página 4

PME120-AI / PME120-AN (CONTRAC) ELECTRICAL ROTARY ACTUATOR | DS/PME120-EN REV. D Rapid traverse mode Ambient conditions The actuator is operated exactly in the same operating mode as in the analog control mode. On activation of digital inputs 2 or 3, the actuator moves at twice the rated operating speed and half the torque in the corresponding direction. Just before the end position is reached, the actuator travel speed is automatically switched back to the set speed, at which the remaining distance is covered. Temperature Different temperature versions are available, depending on the...

Abrir o catálogo na página 5

PME120-AI / PME120-AN (CONTRAC) ELECTRICAL ROTARY ACTUATOR | DS/PME120-EN REV. D — Communication The PROFIBUS DP®, PROFIBUS DP®/V1 or HART® communication protocols are available for digital communication. PROFIBUS® PROFIBUS DP® is an international, open field bus protocol which has been standardized in the field bus standard EN 50170. On a cyclic basis, the master reads the input information from the slaves and writes the output information to the slaves. In addition to this cyclic data transfer of the process representation (e. g. setpoint and actual value), Profibus DP also provides...

Abrir o catálogo na página 6

PME120-AI / PME120-AN (CONTRAC) ELECTRICAL ROTARY ACTUATOR | DS/PME120-EN REV. D — Specification Control actuator PME120-AI Operating mode ≤ 95 % annual average; condensation not permitted Ambient temperature Transport and storage temperature Long-term storage temperature Mounting position 2-layer component epoxy (RAL 9005, black) Anti-condensation heater Power supply for motor and sensors Via Contrac electronic unit only Connection cable actuator – electronic unit Optional (separate power supply or power feed from Contrac electronic unit) optional 5 m (16 ft), 10 m (32 ft) or 20 m (65 ft)...

Abrir o catálogo na página 7

PME120-AI / PME120-AN (CONTRAC) ELECTRICAL ROTARY ACTUATOR | DS/PME120-EN REV. D — … Specification Electronic unit Note Detailed information on separate electronic units can be found in the corresponding data sheets. Power supply PME120-AI / LME620-AI Supply voltage Current consumption at the electronic unit [A] lpos (115 V + 230 V): approx. 40 to 50 % of lmax (AC 115 V / AC 230 V) Actuators for low temperature design External fuse Communication Conventional communication Analog input Analog output 0 / 4 to 20 mA, electrically isolated, max. load 500 Ω Digital 0: −3 to 5 V or open,...

Abrir o catálogo na página 8

PME120-AI / PME120-AN (CONTRAC) ELECTRICAL ROTARY ACTUATOR | DS/PME120-EN REV. D 0×9655 Actuators with DP/V0 communication (cyclic data traffic) 0×09EC Actuators with DP/V1 communication (cyclic and acyclic data traffic) Communication protocol PROFIBUS PA® Profile V3.0 Class B in accordance with IEC 50170 / EN 50170 (DIN 19245) Twisted, shielded copper wire acc. to IEC 50170 / EN 50170 Permissible baud rates 93.75 Kbit/s 187.5 Kbit/s 500 Kbit/s 1500 Kbit/s Automatic baud rate detection 0 to 126, default address 126 Set Slave Address service is supported Connectable active bus termination....

Abrir o catálogo na página 9

PME120-AI / PME120-AN (CONTRAC) ELECTRICAL ROTARY ACTUATOR | DS/PME120-EN REV. D — … Specification Delivery state The standard delivery scope includes metric cable entry threads with IP66 seal plugs. Optional NPT and PG adapters are available. The individual actuator configuration may vary from the standard setup above. This information can be displayed via the user interface. Unless otherwise specified by the user, the electronic units are delivered with the following standard configuration: PROFIBUS DP® communication Parameter Function selection Positioner, parameter: set point Linear;...

Abrir o catálogo na página 10

PME120-AI / PME120-AN (CONTRAC) ELECTRICAL ROTARY ACTUATOR | DS/PME120-EN REV. D — Electrical connections Wire cross-sectional areas Control actuator Electronic unit Actuators with separate electronic unit Crimp pins Motor / brake / heater Contact surface Motor / brake / signals: flexible: 0.5 to 4 mm2 (20 to 12 AWG) Actuators with separate electronic unit EAS822 – Clamping connection Screw terminals (optional) Motor / brake / heater / signals 0.2 to 2.5 Contact surface Suited for cable Ø Terminals for conductor Motor / brake / signals: Actuators with integrated electronic unit Transmitter...

Abrir o catálogo na página 11