Product Information zwickiLine materials testing machines Z0.5 up to Z2.5 zwickiLine range with testControl II electronics zwickiLine with CE-compliant safety device Range of application zwickiLine is a powerful, flexible and cost-effective testing solution for many different materials and components and is ideal for both research and development and routine quality assurance. A wide range of equipment options allows zwickiLine to be used for tests on plastics, elastomers, metals, composites, paper, board, textiles, foams, foodstuffs and components. Innovative high-quality load-frame design • The new zwickiLine extruded profile possesses 6 continuous, freely accessible standard-profile slots for individual mounting of specimen materials, fixtures, safety devices, accessories etc. • The generous test-area depth enables larger fixtures to be used and larger components tested, the wide base crosshead enabling optimum securing and retaining. • High-quality machine design, including for example hard-wearing ceramic control buttons for the electronics, ensures a long service life. Made in Germany zwickiLine, including all mechanical, electronic and software components, together with the extensive range of accessories are developed and produced at Zwick Roell’s production facility in Germany and are therefore ideally matched to each other. This means that zwickiLine is an extremely high-quality product and also allows Zwick to offer the best possible support. Powerful drives Extremely low minimum speeds can be set, combined with excellent speed-accuracy. The drive also delivers high crosshead travel resolution; this is important in tests on components requiring a high degree of travelprecision and in tests on specimens with high levels of stiffness and low travel, for example. The high test speed range can be used without restriction. In addition, test loads up to 110% of the machine nominal load are permissible to compensate for heavy combinations of test fixtures, accessories etc. High stiffness and precision crosshead guide The stiff load-frame profile and large connecting surfaces reduce the inclination angle of the crosshead under load, enabling very precise alignment and application of force to the specimen. This is advantageous for flexure tests, compression tests, precision tests on components etc. Safety for you and the entire testing system, and the modern safety device Features ensuring safety include the 2-channel (= double safeguard) safety circuit, operating-mode selectorswitch and Drive Off switch. The operator is shielded from flying specimen fragments or other hazards by the CE-compliant safety device featuring a large test area, transparent design and excellent accessibi

Product Information zwickiLine materials testing machines Z0.5 up to Z2.5 Powerful, innovative testControl II electronics zwickiLine is equipped with testControl II digital measurement and control electronics, mounted vertically on the load frame for better protection against ingress of liquids or conductive particles. testXpert II – intelligent and reliable testXpert II testing software and testControl II electronics are perfectly matched, ensuring safe, efficient, reliable operation of the materials testing machine. testXpert II offers the optimum solution for any testing requirement. Built-in...

Product Information zwickiLine materials testing machines Z0.5 up to Z2.5 Data Value Load frame Finish RAL 7021 black grey and RAL 7037 dusty grey Ambient temperature +10 ... +35 °C Air humidity 20 ... 90 % Conformity to ISO 9000 and CE Antrieb Motor DC servo-motor Input signal, set-value preset digital Controller / Cycle time adaptive / 1000 Hz Positioning, repetition accuracy ±2 μm Measurement and control electronics Number of slots available for measurement 2 synchronized module bus slots (expandable to 5)(1 and control modules 1 synchronised PCIe slot Force measurement Grade 0.5 / 1 see load...

All data at ambient temperature. With option „Additional crosshead“ height is increased by 9 mm Width option „Large base“: Width 586 mm, Depth 565 mm, Depth with electonics console 707 mm (3 See drawing on page 2 (4 With option the speed can be increased up to 3000 mm/min Drive system Crosshead speed vmin ... vnom Drive system’s travel resolution Positioning, repetition accuracy Load frame Test load FN in tensile/compression direction 0.5 0.5 0.5 1 1 1 2.5 2.5 (1 Height ca. 789 1289 1589 789 1289 1589 789 1289 Width(2 408 408 408 408 408 408 408 408 Width (with electronics console)(2 411 411...