Laser Dust Sensor (Model: ZH06-III) Manual Version: 1.4 Issue Date: 2023-06-27 Zhengzhou Winsen Electronics Technology Co., Ltd

Statement This manual copyright belongs to Zhengzhou Winsen Electronics Technology Co., LTD. Without the written permission, any part of this manual shall not be copied, translated, stored in database or retrieval system, also can’t spread through electronic, copying, record ways. Thanks for purchasing our product. In order to let customers using it better and reduce the faults caused by misuse, please read the manual carefully and operate it correctly in accordance with the instructions. If users disobey the terms or remove, disassemble, change the components inside of the sensor, we shall not...

Zhengzhou Winsen Electronics Technology Co., Ltd ZH06-III Laser dust sensor Description: Laser Dust sensor module is a common type, small size sensor, using laser scattering principle to detect the dust particles in air, with good consistency and stability. It is easy to use, with UART & PWM output; Small size is suitable for Dust Collecting Hole Table 1. Technical parameters Features: Good consistency Real time response Accurate data Detection Range Effective Range Detection Interval Low power consumption Minus resolution of particle diameter Detection Accuracy (Test Condition: 25 ± 2 ℃, 50...

Zhengzhou Winsen Electronics Technology Co., Ltd Terminal Description：1.25T-8P Connector，Pin Spacing 1.25mm，Pin Qty：8 RXD Serial port receive pin Email: [email protected] Leading gas sensing solutions supplier

Laser Dust Sensor UART settings Baud rate Date bits Stop bits Please refer the document of ZH06 I-IV Series Communication Protocol. Principle Description: Email: [email protected] Leading gas sensing solutions supplier in China!

Laser Dust Sensor Sensor Construction: Installation Method: The dust collection hole is the air inlet inside the sensor, which needs to keep good contact with the external air; the fan is installed at the air outlet inside the sensor. When the sensor is installed and working, must avoid strong airflow interference around the sensor; if it cannot be avoided, try to keep the external airflow direction perpendicular to the internal airflow direction of the sensor. When designing the detection cavity of the whole machine, the effective area of the sampling port of the sensor should be fully considered...

Laser Dust Sensor Email: [email protected] Leading gas sensing solutions supplier in China!

Laser Dust Sensor Typical Output Characteristics: Fig10 Note: The picture shows the data comparison between the conventional ZH06 laser particle sensor and TSI8530 in the test environment. Abscissa : Testing time related parameters Ordinate : The concentration of particles in the test environment (with TSI8530 data as reference, unit: μg /m³, environmental resolution: 1μg/m³). Attentions: 1. It is forbidden to remove the shield cover of the sensor and the internal fixing screw of the sensor, because the shield cover of the sensor is connected with the internal power supply of the sensor through...

Laser Dust Sensor environment, too large dust particles, high humidity environment, such as: kitchen, bathroom, smoking room, outdoor environment, etc. If it is used in such environments, corresponding protective measures shall be added to the user's equipment to prevent viscous particles or large particles from entering the interior of the sensor and forming accumulation in the interior of the sensor which will affect the performance of the sensor. (for example, in the working environment with floccules or fibers, the corresponding coarse filter net should be added ahead the air inlet of the...

Laser Dust Sensor Packing: 1. Put the sensor into the Pearl Foam Tray as shown in the picture below. 2. Put the whole plate of sensors in Small Box one by one, then puts a foam plate at the top. Each Small Box can hold 25 sensors. 3. Select the appropriate carton according to the quantity of the order: Carton F: 355 x 310 x 285mm, can hold 200 sensors, total weight around 6.2kg. Carton D: 630 x 280 x 405mm, can hold 600 sensors, total weight around 18.0kg. Note: Please pay attention to water proof of the carton during transportation Email: [email protected] Leading gas sensing solutions supplier...

Laser Dust Sensor Reliability Testing: Testing Testing Condition Decision Criteria Number of Tests - n Number of Failures - c Zero output The test cabin meets the Zero point output range: ＜15μ Record the output value of the sensor for 6 times at each detection accuracy" Zero point output range: ＜15μ Measure the output range and mass concentration of dust is not more than 5.0 μ g / m³, the sensor is powered on, and the output value is recorded six times. concentration of 50, 130 and 260μ g/m³, totally 18 times, take the maximum value respectively relative error of zero point. When the output value...

Laser Dust Sensor Power on/off Zero point output range: ＜15μ output range of zero point and relative error after completion. The background noise is less than 30dB (a), the sensor works stably for 20min, and the sound level meter is placed on the same horizontal plane 0.8m high from the ground. The distance between the two is 1m. Each measurement is conducted three times, and the maximum value is taken There shall be no obvious dents, under the environment condition scratches, cracks, deformation and other defects on the sensor and stable at room temperature surface, no bubbles, crazing and range...

Laser Dust Sensor 2h, Measure zero point output range after completion There shall be no obvious dents, scratches, cracks, deformation range: (10-150) Hz; Sine amplitude: 1.5mm; Frequency range: 1oct; X, y, Z three axes, each sweeping 15 times. Measure the output range of zero point and relative error after completion. 13 Zero point output range: ＜15μ Drop Test and other defects on the sensor surface, no bubbles, crazing and falling off on the coating and coating, no loosening and falling off on the connectors and parts, no rust and mechanical damage on the metal components. Zero point output...