Laboratory Power Supply ZAS Series High Power Progammable DC Power Supply 600W – 7200W / 10VDC – 120VDC Units for Laboratory and Test Zero voltage soft switching technique, low ripple and noise Use of reliable digital encoder for voltage and current setting Micro controller for digital programming Constant Voltage / Constant Current Mode with auto mode crossover LabView and LabWindows drivers Activer PFC at the input with wide input window Four digit seven segment LED display for voltage and current read back 19“ rack mount suitable for ATE and OEM applications Parallel operation with active Current Sharing RS232, RS485, GPIB interface for external programming Galvanic isolated analog programming and mounting surface Optional: Ethernet interface card-kit ZAS Series of programmable DC Laboratory Power Supplies are most flexible and reliable AC/DC Power Systems for OEM, Industrial and Laboratory applications. These are designed with excellent thermal management and can be conveniently stacked in 19” rack mounts without any space between them for ventilation. The zero voltage soft-switching technique employed in them virtually eliminates the switching transients to derive lower noise, which is closer to linear level. This technique also helps increasing the overall conversion efficiency which in turn decreases the heat generation, thus reducing the stress on the power components which results in greater reliability. Input: Input voltage Power Factor Switching frequency Inrush current Output: Output DC voltage Output DC current Time delay Output Noise (90-20MHz) Rippel (RMS) Efficiency Hold up time Constant Voltage (CV), constant current (CC) mode with auto crossover 600W, 1200W: 95..264VAC, 45..63Hz, p Phase, 2400W: 175..264VAC, 45..63Hz, 1 phase 3600W, 7200W: 300…457VAC, 45..63Hz, 3 phase, 4 wire 0,99 typ., full load, nominal line 45kHz nominal limited by NTC see table see table 7s max. from power ON until output stable voltage <45mV p-p see table minimum 80%, typical 20ms Regulation: Line regulation voltage 0.1% Vout current 0.1% I out Load regulation voltage 0.1% U out current 0.1% I out Voltage mode transient Response <200μs, for load change 40..90% Stability 0.05% Temperatur Coefficient Voltage 0.05% (V max/°C) Current 0.05% (I max/°C) Overvoltage control yes Protection: Voltage differential Over temperature protection Over voltage control Over voltage protection Remote sensing min. ± 600VDC, output to safety ground Through 90°C thermal switch on heat sink yes programmable through rotary encoder or digital interface yes Environmental conditions: Operating temperature Storage temperature Humidity Cooling 0..+50°C, Derating>40°C, 2.5%/°C -20..+70°C ≤ 90% RH non condensing Internal forced air cooling from front to rear side with zero stacking Safety: Safety standard Operation and Control: Parallel operation Sense operation Meters with active Current Sharing possible LED display Voltage: set voltage, set overvoltage 7 Segment, 4 Digit Current: set current,7 Segment, 4 Digit Accuracy 0.2% +/-3 counts Front panel controls Last set memory Remote ON/OFF Display Digital rotary encoder for voltage, current and over voltage set yes LED for CV, CC, Remote, Output ON, Trip, Remote, Uset, Iset, OVset, Set Mode zentro-elektrik GmbH KG | Tel.: ++49 (0) 7232-31310 | Fax: ++49 (0) 7232-3131399 | E-mail: [email protected]

Programming and Interface: Remote analog programming Voltage and current, input isolated 0..5V (default), or 0..10V or 0..4.85k for 0..100% Remote analog monitoring Isolated voltage and current monitoring output 0..5V (default), or 0..10V Accuracy, monitoring and programming 0.5% for 0..100% output Remote sense compensation max.,1V/wire Digital interface RS232, standard Electrical connections: Input 600W: 10A, 250V line socket 1200W: 16A, 250V line socket/3core 2400W: 3 way terminal 30A, 415V terminal block/3core 20A,250V line cord without plug 3600W: 4 way terminal 30A, 250V terminal block 7200W:...

Laboratory Power Supply Front View 600W/1000W/1200W 3 ZAS Front View 1. Main ON/OFF switch 2. Three digit display for output voltage / set voltage / set over voltage indication 3. Three digit display for output current / set current indication 4. Digital rotary encoder for ouput voltage, current and over voltage limit settingsg 5. Push switch to view set parameters in SET mode 6. Push switch for ouput ON / OFF control 7. LED indication for CV, CC, Output ON, Trip, Remote, Vset, Iset, OVset, and Set Mode ZAS Rear View 8. Line input 9. Input fuse 10. DC output terminals 11. 3.5mm 8Pin remote sense...