Innovative Service Around the Globe DATA SHEET THICK FILM CHIP RESISTORS RoHS compliant & Halogen free

Product specification Chip Resistor Surface Mount ORDERING INFORMATION - GLOBAL PART NUMBER This specification describes AC0201 to AC2512 chip resistors with leadfree terminations made by thick film process. Part number is identified by the series name, size, tolerance, packaging type, temperature coefficient, taping reel and resistance value. APPLICATIONS  All general purpose applications  Car electronics, industrial application FEATURES  AEC-Q200 qualified  Moisture sensitivity level: MSL 1  AC series soldering is compliant with J-STD-020D  Halogen free epoxy  RoHS compliant - Products...

Product specification Chip Resistor Surface Mount E-24 series: 3 digits, ± 5% First two digits for significant figure and 3rd digit for number of zeros E-24 series: 3 digits, ± 1% & ± 0.5% One short bar under marking letter E-96 series: 3 digits, ± 1% & ± 0.5% First two digits for E-96 marking rule and 3rd letter for number of zeros Fig. 4 Both E-24 and E-96 series: 4 digits, ± 1% & ± 0.5% First three digits for significant figure and 4th digit for number of zeros Fig. 5 Value = 10 KΩ E-24 series: 3 digits, ± 5% First two digits for significant figure and 3rd digit for number of zeros Fig. 6...

Product specification Chip Resistor Surface Mount CONSTRUCTION The resistors are constructed on top of an automotive grade ceramic body. Internal metal electrodes are added at each end and connected by a resistive glaze. The resistive glaze is covered by a lead-free glass. The composition of the glaze is adjusted to give the approximately required resistance value and laser trimming of this resistive glaze achieves the value within tolerance. The whole element is covered by a protective overcoat. Size 0603 and bigger is marked with the resistance value on top. Finally, the two external terminations...

YAGEO Phfcomp Chip Resistor Surface Mount

YAGEOI Phfcomp Product specificcrlion Chip Resistor Surface Mount

YAGEO Phfcomp Chip Resistor Surface Mount

Product specification Chip Resistor Surface Mount FOOTPRINT AND SOLDERING PROFILES Recommended footprint and soldering profiles of AC -series is the same as RC-series. Please refer to data sheet “Chip resistors mounting”. PACKING STYLE AND PACKAGING QUANTITY Table 3 Packing style and packaging quantity PACKING STYLE Paper taping reel (R) Embossed taping reel (K) 1. For paper/embossed tape and reel specifications/dimensions, please refer to data sheet “Chip resistorsRESISTANCE TEMPERATURE COEFFICIENT OF packing”. RESISTANCE RANGE > 100 mΩ ± 75 ppm/°C ± 75 ppm/°C Fig. 10 Maximum dissipation (P...

Product specification Chip Resistor Surface Mount TESTS AND REQUIREMENTS Table 4 Test condition, procedure and requirements TEST TEST METHOD High Temperature Exposure Moisture Resistance Each temperature / humidity cycle is defined at 8 hours (method 106F), 3 cycles / 24 hours for 10d. with 25 °C / 65 °C 95% R.H, without steps 7a & 7b, unpowered Parts mounted on test-boards, without condensation on parts Biased Humidity Operational Life Measurement at 24± 4 hours after test conclusion. 1,000 hours; 85 °C / 85% RH 10% of operating power 1,000 hours at 125 °C, derated voltage applied for 1.5 hours...

Product specification Chip Resistor Surface Mount TEST Solderability - Wetting TEST METHOD Electrical Test not required Magnification 50X SMD conditions: (a) Method B, aging 4 hours at 155 °C dry heat, dipping at 235± 3 °C for 5± 0.5 seconds. REQUIREMENTS Well tinned (≥95% covered) No visible damage (b) Method B, steam aging 8 hours, dipping at 215± 3 °C for 5± 0.5 seconds. (c) Method D, steam aging 8 hours, dipping at 260± 3 °C for 7± 0.5 seconds. Board Flex Chips mounted on a 90mm glass epoxy resin PCB (FR4) Bending for 0201/0402: 5 mm 0603/0805: 3 mm 1206 and above: 2 mm Holding time: minimum...

YAGEO Phtcomp Chip Resistor Surface Mount I AC | SERIES | 0201 to 2512 REVISION DATE CHANGE NOTIFICATION DESCRIPTION ■ Extend resistance range ■ Update FOS test and requirements ■ Feature description updated ■ delete 10" taping reel ■ Jumper criteria added ■ AC 1218 marking and outline figure updated ■ Case size 1210, 1218, 2010, 2512 extended ■ Test method and procedure updated ■ Packing style of 7D added First issue of this specification

Product specification Chip Resistor Surface Mount LEGAL DISCLAIMER Yageo, its distributors and agents (collectively, “Yageo ”), hereby disclaims any and all liabilities for any errors, inaccuracies or incompleteness contained in any product related information, including but not limited to product specifications, datasheets, pictures and/or graphics. Yageo may make changes, mod ifications and/or improvements to product related information at any time and without notice. Yageo makes no representation, warranty, and/or guarantee about the fitness of its products for any particular purpose or the...