Catalog excerpts
E-mail : sales@SETfuse.com All Rights Reserved by Xiamen SET Electronics Co., Ltd. 2021-2023
Open the catalog to page 4E-mail : sales@SETfuse.com All Rights Reserved by Xiamen SET Electronics Co., Ltd. 2021-2023
Open the catalog to page 5E-mail : sales@SETfuse.com All Rights Reserved by Xiamen SET Electronics Co., Ltd. 2021-2023
Open the catalog to page 6HIGH ACCURACY OF FUNCTIONING TEMP. NON-RESETTABLE OVER TEMP. PROTECTION SEALED CONSTRUCTION RATED FUNCTIONING TEMP.: (76 to 230) °C RoHS & REACH COMPLIANT E-mail : sales@SETfuse.com All Rights Reserved by Xiamen SET Electronics Co., Lt
Open the catalog to page 7Description Alloy Thermal-Link / Alloy Thermal Cutoff (ATCO) is defined as a non-resettable protective device functioning one time only. It is widely used in electrical equipment. ATCO is mainly consist of Fusible Alloy, Flux Resin, Case, Sealant and Lead Wires. Normall y, Fusible Alloy is jointed to the two Lead Wires. Under abnormal conditions, when the Temp. reaches to the fusing Temp. of AT CO, the Fusible Alloy melts and quickly retracts to the two Lead Wire ends with the aid of the Flux Resin and disconnects the cir cuit completely. SETsafe | SETfuse ATCO is classified into Axial and...
Open the catalog to page 8Power Supply Home Electrical Appliances Power Strips Electric Heating Appliances Operation Principle Fusible Alloy Flux Resin Case Sealant Epoxy Lead Wire After Functioning Before Functioning Fusing Diagram (For reference only) Diagram of melting point test for Fusible Alloy Under abnormal conditions, when the Temp. reaches to the fusing Temp. of ATCO, the Fusible Alloy melts and quickly retracts to the two Lead Wire ends with the aid of the Flux Resin and disconnects the circuit completely. E-mail : sales@SETfuse.com All Rights Reserved by Xiamen SET Electronics Co., Ltd
Open the catalog to page 9Part Number System ATCO - T 115 - A N N A B - 001 Serial Number Packing B Leads Forming Single Lead Bending Leads Bending Leads Kinking Leads Bending Color of Insulation Tube W Insulation Tube Material T Lead Wire Type A Tinned Copper Wire Tinned Copper Clad Steel Wire Rated Functioning Temp. 115 Series, Refer to specifications Product Category ATCO Thermal-Link E-mail : sales@SETfuse.com All Rights Reserved by Xiamen SET Electronics Co., Ltd. 2021-2023 Straight Lead
Open the catalog to page 10Leads Forming Types The below leads forming are for reference only, more leads forming can be customized. Axial Type C Glossary Item A non-resettable device incorporating a THERMAL ELEMENT which will open a circuit once only when exposed for a sufficient length of time to a temperature in excess of that for which it has been designed. — (IEC 60691) E-mail : sales@SETfuse.com All Rights Reserved by Xiamen SET Electronics Co., Ltd. 2021-2023
Open the catalog to page 11Alloy Thermal-Link Alloy Type Thermal-Link, Alloy is the thermal element. Rated Functioning Temp. The temperature of the Alloy Thermal-Link which causes it to change the state of conductivity with a detection Tf current up to 10 mA as the only load. Tolerance: Tf ± 7 °C (J60691). Fusing Temp. The temperature of the Alloy Thermal-Link which causes it to change its state of conductivity is measured with silicone oil bath in which the temperature is increased at the rate of 0.5 °C to 1 °C / minute, with a detection current up to 10 mA as the only load. The maximum temperature at which a Alloy...
Open the catalog to page 121. When atmosphere pressure is from 80 kPa to 106 kPa, the related altitude shall be from 2000 meter to -500 meter. 2. Operating voltage should be less than rated voltage of ATCO, operating current should be less than rated current of ATCO. 3. Do not touch the ATCO body or lead wires directly when power is on, to avoid burning or electric shock. Replacement ATCO is a non-repairable product. For safety sake, it shall be replaced by an equivalent ATCO from the same manufacturer, and mounted in the same way. Storage Do not store the ATCO at the high Temp., high humidity or corrosive gas...
Open the catalog to page 13Thermal-Link Installation position of mechanical performance requirements. 1. Do not locate the ATCO in a place where severe vibration always occurs. 2. Ensure that the lead wire is long enough, and avoid actions such as press, tensile or twist. 3. The seal or body of TCO must not be damaged. Mechanical Connection Riveting 1. Choose small resistivity riveting material and be riveted. 2. A flexible lead or lead with low resistance should be used to rivet the ATCO. 3. Contact resistance should be minimal, large contact resistance will lead to higher Temp.rising, ATCO Functioning in ad-...
Open the catalog to page 14Soldering Position Body Soldering Position Body Soldering Position FIGURE T-1 TABLE T-2 Wave Soldering Parameters Setting Max. Allowable Preheating Temp. When the Length of Lead Wire is Different(Fig.T-1) Preheating Temp. Preheating Temp. Max. Wave Soldering Temp. Recommend Hand-Soldering Max. Wave Soldering Temp. Preheating Temp. E-mail : sales@SETfuse.com All Rights Reserved by Xiamen SET Electronics Co., Ltd. 2021-2023 Rated Functioni
Open the catalog to page 15Lead Wire Forming 1. If lead wire has to be bent, please pay attention to the distance between body and bending point. Refer to Table T-3, T-4. 2. When bending leads, please use pincher or similar tools to fix the product as shown in Fig.T-2, T-3, to avoid damaging the product. 3. During forming and mounting, lead wire should not be cut, nicked, bent sharply, to avoid breaking the product. 4. Tangential forces on the leads must be avoided (i.e. pushing or pulling on the leads at angle to ATCO body) as such forces may damage the seal of ATCO. Fixing Position Fixing Position d FIGURE T-2...
Open the catalog to page 16Switched-Mode Power Supplies Home Electrical Appliances The Length of Lead Wires RoHS & REACH Compliant Taping Packing Available Lead Wires can be Insulated Tinned Copper Wires or CP Wires High Accuracy of Functioning Temp. Agency Approvals Agency Mark E-mail : sales@SETfuse.com
Open the catalog to page 17Fusing Temp. RoHS REACH
Open the catalog to page 18Product Temp.-Time Curve ( For reference only ) The Temp.-Time Curve of Thermal-Link in different Temp. oil baths. E-mail : sales@SETfuse.com
Open the catalog to page 19Product Current-Time Curve (For reference only) The Current-Time Curve shows functioning time at multi-times rated current at room temperature 25 ± 2 °C. E-mail : sales@SETfuse.com All Rights Reserved by Xiamen SET Electronics Co., Ltd. 2021-2023
Open the catalog to page 20All Xiamen SET electronics Co. catalogs and technical brochures
-
HS Series Ir : 5 A
10 Pages
-
SD Series Ir : 10 A
11 Pages
-
XM Series Ir : 3 A
11 Pages
-
TM Series Ir : 15 / 16 A
11 Pages
-
T Series Ir : 15 / 16 A
11 Pages
-
P Series Ir : 20 A
10 Pages
-
Y Series Ir : 5 A
12 Pages
-
TK Series Ir : 15 / 16 A
11 Pages
-
XG Series Ir : 3 A
15 Pages
-
S Series Ir : 10 A
11 Pages
-
KM Series Ir : 2 A
11 Pages
-
Q Series Ir : 25 A
10 Pages
-
SM Series Ir : 10 A
11 Pages
-
SK Series Ir : 10 A
11 Pages
-
SY Series Ir : 10 A
10 Pages
-
SKL Series Ir : 10 A
10 Pages
-
KG Series Ir : 2 A
12 Pages
-
YM Series Ir : 5 A
14 Pages
-
X Series Ir : 3 A
12 Pages
-
K Series Ir : 2 A
12 Pages
-
TPH×××-R Series
7 Pages
-
SC625 series
8 Pages
-
SMF Series
11 Pages
-
F Series
12 Pages
-
E-All Products Catalog(2021-2023)
1103 Pages