Capacity Type Pulse Magnetizing Power Operation manual Please carefully read this instruction manual before usage, and use the instrument according to correct method of operation. Be sure to read the “Safety” and “Cautions” before using the instrument. Carefully preserve this manual, to ensure that it will never be lost. If you have any matter unclear of encounter any trouble, etc. in the use of the instrument, do not hesitate to contact us. Xiamen Dexing Magnet

Thanks you to use our company’s capacity type pulse magnetizing power. We are committed continuously to improve product quality and development, for which we retain this right that is in this manual for product specifications and technical parameters of improvement without prior notice. We do our best to ensure the accuracy of the information in this manual, but for any errors, we do not assume any responsibility. We strive to improve product quality, while provide effective, fast technical support for customers.

CONTENTS 1 Safety Precautions ………………………………………………………………… 1 2 General ……………………………………………………………………………… 5 2-1Feature……………………………………………………………………………… 5 2-2 Instrument type and selection methods..………………………………………………5 2-3 Energy selection method………………………………………………………………5 3 Specifications …………………………………………………………………… 6 4 Method of operation and usage……………………………………………………………7 4- 1 Funct i on …… … … …… …………………………………………………… 7 4-2 Ambient requirements……………………………………………………………… 8 4-3 Installation and Connection………………………………………………………… 9 4-4 Method of operation………………………………………………………

1 Safety precautions Before using the equipment, read the following instructions without fail. When using the magnetizer power supply equipment, read the instruction manual supplied with each product thoroughly. It is also recommended to handle the equipment properly while taking adequate care for safety. Throughout discriminated by ranking as “DANGER”, “WARNING”, and “CAUTION”. In case where there is a high possibility that severe personal injury or death is caused if any safety instruction is ignored. This safety instruction is represented as ! DANGER. In case where there is a high possibility...

1-phase AC 220V and the ground connection wire(green) to the factory ground connection. • Before making wirings for the output terminal, be sure to turn off all phases of the factory power source and turn off the power circuit breaker of the equipment. • This equipment employs high voltages, and if it is handled incorrectly, it is dangerous. Before making wirings of loads (magnetizing yoke and magnetizing coil), be sure to confirm that no charge voltage remains. • Connect metal portion of the magnetizing yoke(yoke portion) and magnetizing coil(bobbin portion) to the factory ground connection....

• In the event that any abnormal operation such as malfunction of the equipment is noticed, immediately stop use of the equipment and contact us. • This equipment uses high voltages. Therefore, avoid installation in a place with much dirt, oil and fume, conductive dust, corrosive gases and/or inflammable gases, or in a place subjected to high temperature and dew formation, as it may cause this equipment to be damaged or deteriorated or to malfunction. install the equipment in a well-ventilated, less dusty and dry place. • When operating this equipment, be sure not to place around it any object...

charge and magnetic properties of the industry’s requirements, such as ferrite multi-pole permanent magnet magnetization (including radial, axial, plane, spoke to the ring), rare earth permanent magnetic materials multi-polar magnetization (including radial, axial, plane, spoke to the ring). DXME series magnetizing power, that is, high voltage, high current, capacity type discharge impulse magnetizer power. As the charge on the capacitor energy storage is sufficient, magnetizing or demagnetizing load instantaneous release (release time is typically < 100uS, depending on the load impedance parameters...

No special function 2-3 Energy selection method Capacitor discharge energy according to the formula, through the device's model number can be calculated by the energy: P = (1 / 2) * CU2 convenient to calculate a specific type of magnetizing power of the maximum discharge energy, but also can be used for selection use. For example: DXME-10C200 -6 DXME magnetizing power of the full range of products see below with the product data sheets for the selection of use. 3 Technical Specification （1）Power input