Intelligent Temperature and Vibration Combined Sensor Description CS-iWPVT-01 is a combined sensor integrating temperature, vibration, and pressure acquisition by Bluetooth communication mode. It uses a three-axis accelerometer as a detection unit to collect acceleration, while collecting equipment surface temperature, and occasions where pressure data needs to be collected, broadcasts data regularly in Bluetooth transmission, and conducts near-end monitoring, detection, analysis, and judgment of vibration, temperature and pressure and other parameters in the industrial machinery environment through data analysis, so as to realize the predictive health management of equipment failure to reduce the economic loss caused by equipment failure. The terminal uses a built-in disposable lithium battery. The Intelligent Temperature and Vibration Combined Sensor uses a small 32-bit low-power ARM processor and integrates the BLE 5.0 protocol stack, so that the sensor has a higher level of integration and smaller size. The sensor is powered by disposable lithium battery, built-in high-precision acceleration sensor and high-sensitivity temperature sensor for acceleration acquisition, frequency solving and device surface temperature measurement. At the same time, the sensor contains an external pressure interface. The sensor can perform timing sampling and alarm settings on the sensor according to the set collection time, and the data is sent to the APP through Bluetooth, so that the data could be easily obtained on the mobile phone.

Intelligent Temperature and Vibration Combined Sensor Note: The above parameters only apply to the Intelligent Temperature and Vibration Combined Transmitter.

CS-iWPVT-01Intelligent Temperature and Vibration Combined SensorStructure and Dimension (mm) Communication Protocols Broadcast packets 1

Intelligent Temperature and Vibration Combined Sensor Power on default to send non-connectable broadcast data (data format as shown above), use the magnet close to the top of the device for more than 1 second, and then take away, The device switches to connectable broadcast, at this time using the mobile phone to connect the device after sending instructions in the Bluetooth APP to modify the configuration parameters (broadcast interval, sampling interval), you can also send instructions to obtain the sampling data stored in flash. The storage data format is as follows:

Intelligent Temperature and Vibration Combined Sensor Fix the product on the M6 stud position. Note: The specific installation location is determined according to the on-site installation environment. 1. The measured temperature and vibration device. 2. The measured pressure device. 3. Pressure sensor ( optional). 4. Intelligent temperature, vibration and pressure sensor.

CS-iWPVT-01Intelligent Temperature and Vibration Combined SensorOrder guidance CS-iWPVT-01 Order code information graphic: Product name Pressure sensors NP = No pressure sensor (default) P = Equipped with pressure sensor Intelligent Temperature and Vibration Combined Transmitter needs to be with pressure sensor. Note: If integrated with pressure sensor, the relative parameters need to be confirmed when placing the order.

CS-iWPVT-01Intelligent Temperature and Vibration Combined Sensor Notes 1) The installation of sensors must be firm to ensure reliable and stable monitoring data. 2) Battery Level Description a. The battery life is estimated under the condition of collecting once every 1 minute and broadcasting once every 10 seconds. The Intelligent Temperature and Vibration Combined Transmitter strictly meets the technical requirements of product life. b. Based on the discharge characteristics of the lithium sub-battery (Figure 3), it is close to the inflection point of the discharge curve, and the detection...

CS-iWPVT-01Intelligent Temperature and Vibration Combined Sensor Fault phenomenon Disposal methods of hazardous wastes such as waste circuit boards and their components after the end of product life. After the end of the product life, each part shall be distinguished according to the “National hazardous waste list” to determine whether it is hazardous waste. Among them, the waste lithium battery not disassembled is not hazardous waste, and the waste circuit board (including components, chips, plug-ins, pins, etc. attached to the waste circuit board) belongs to hazardous waste. The part that is...

CS-iWPVT-01 Intelligent Temperature and Vibration Combined Sensor Statement The company reserves the right to modify the specifications and contents of this manual. Subject to modification without notice. Due to the update of the product, the individual details of this document may not match the product, please refer to the actual product. The interpretation right of this document belongs to our company.