Strain sensor with mV/V-output (DMS measuring bridge)
7Pages

{{requestButtons}}

Catalog excerpts

Strain sensor with mV/V-output (DMS measuring bridge) - 1

For 0.250 Mm/m with very high sensitivity • Very flat design with only 6.5 mm height • Very high sensitivity and resolution • Strain sensor with mV/V-output (DMS measuring bridge) • For static and dynamic applications • For force, weight and deformation measurements • Measuring very small strains in rigid structures Surface strain sensor X-103 monitors the strain between its two mounting screws and amplifies this mechanically. In this way the strain is concentrated in the measuring area and can therefore be measured using a resistive strain gauge bridge. These strain sensors are used if the mV/V-signal of a DMS measuring bridge is used if more than one strain sensor should be connected in parallel. This is the case for weight measurements and for force measurement at several tie-bars of a press. The strain sensor will generate a proportional DMS bridge signal (mV/V) depending on the stress of the structure. An extremely solid steel housing, combined with IP65 protection guarantees trouble-free operation, even under harsh and rugged environment conditions.

Open the catalog to page 1
Strain sensor with mV/V-output (DMS measuring bridge) - 2

Measuring Bridge Output signal Ordering coderange resistance X-103-D10 M12 plug 0...250 [Jm/m 350 Ohm +1.0 mV/V X-103-D10-M12-350Ohm-CAL250 Order information: Type/Description Measuring range Output signal Cable length / connector Options: CON: Cable connector at the free end LEN: Customer specific cable length Strain sensor with DMS measuring bridge

Open the catalog to page 2
Strain sensor with mV/V-output (DMS measuring bridge) - 3

Strain sensor X-103-D10 with M12 plug 93 x 25 x 14 mm, 4x M6, 0...250 pm/m, +1 mV/V Specifications! Mechanical dimensions! Performance Ordering information This strain sensor is delivered without mounting screws. For detailed ordering information, please see page 2. Strain sensor with DMS measuring bridge

Open the catalog to page 3
Strain sensor with mV/V-output (DMS measuring bridge) - 4

Strain sensor X-103-D15 89 x 26 x 6.5 mm, 4x M6, 0...250 pm/m, +1.5 mV/V Specifications Electrical data Strain sensor with DMS measuring bridge

Open the catalog to page 4
Strain sensor with mV/V-output (DMS measuring bridge) - 5

Strain sensor X-103-D20 89 x 26 x 6.5 mm, 4x M6, 0...1000 pm/m, +2 mV/V Specifications Electrical data Mechanical data Ordering information This strain sensor is delivered without mounting screws. For detailed ordering information, please see page 2. Strain sensor with DMS measuring bridge

Open the catalog to page 5
Strain sensor with mV/V-output (DMS measuring bridge) - 6

Strain sensor X-103-D30 with high sensitivity 89 x 26 x 6.5 mm, 4x M6, 0...250 pm/m, +3 mV/V Specifications! Mechanical dimensions! Performance Strain sensor with DMS measuring bridge

Open the catalog to page 6
Strain sensor with mV/V-output (DMS measuring bridge) - 7

The zero adjustment at the strain sensors with DMS bridge output signal (mV/V) is done at the subsequent amplifier. X-SENSORS offers two different types of amplifiers: One for static applications and one for dynamic applications. For dynamic applications, a digital input for automatic zero-point adjustments is offered. For static applications, the zero point can be adjusted manually by DIP switches and by a potentiometer for fine tuning. The strain sensors should be mounted on machined surfaces N9 with a flatness to within 0,5 mm. Use the following parameter for tighten the socket screws:...

Open the catalog to page 7

All X-Sensors AG catalogs and technical brochures

  1. XCS-131

    7 Pages

  2. X-134

    6 Pages

  3. DB_X-135_V00

    5 Pages