BWK216S Low Cost Single-Axis Digital Output Inclinometer Technical Manual

Low Cost Single-Axis Digital Output Inclinometer Introduction Designed by Bewis Sensing Technology LLC, BWK216S is a low cost single-axis digital output inclinometer, adopting the latest industrial level MEMS accelerometer. Its measuring range is ±180°, highest accuracy is 0.2°, working temperature is -40℃~+85℃, the product with a small size and low weight, can meet space-restricted application requirements. This product converts static gravity field changes into angle changes, It outputs horizontal angle values directly by digital, this product has the advantages of low cost, small temperature...

Specifications@ Electrical Specifications Parameters Resolution: The measured minimum change value that the sensor can detect and resolve within the measurement range. Accuracy: The error between the actual angle and the Root mean square(RMS) of the measured angle of the sensor (>16 times). Bewis SensinglTechnologyiLLCl

BWK 216S Low Cost Single-Axis Digital Output Inclinometer Bare plate product size Product size: L33*W27*H6(mm) Note: ±1mm error for length and width dimensions, please refer to actual size. Bewis SensinglTechnologyiLLCl

Low Cost Single-Axis Digital Output Inclinometer Installation direction The correct installation method can avoid measurement error. The following points should be made when installing the sensor: First of all, to ensure that the sensor mounting surface and the measured surface completely close, the measured surface should be as horizontal as possible, can not have the angle shown in Figure A and Figure C, the correct installation is shown in Figure B and Figure D. A B uneven surface generates the angle D uneven surface generates the angle Secondly, the bottom cable of the sensor and the axis...

BWK 216S I Low Cost Single-Axis Digital Output Inclinometer Elect ri cal connections Electrical interfaces >^RE D VCC > ^YELLOW TXD '^GREEN RXD Bewis SensinglTechnologyiLLCW

Low Cost Single-Axis Digital Output Inclinometer Debug software Users can directly download serial assistant on official website (Supports-Download). You can also use more convenient and intuitive PC software. BWK216S supporting serial debugging software can be connected to the inclinometer on the computer for angle display. The software debugging interface is as shown in the figure below. Using the debug software, it can conveniently display the current X-direction tilt angle, and you can also modify and set other parameters by yourself. Software use steps: ① Correctly connect the inclinometer...

Low Cost Single-Axis Digital Output Inclinometer Protocol 1Data Frame Format： （8 data bits，1 stop bit，No parity check，default baud rate 9600） Identifier (1byte) 0x77 Data Format: Hexadecimal Identifier: Fixed to 77 Frame Length: Length from Frame Length to Checksum（included） Address Code: Address of acquiring module, default 0x00 Data: Content and length variable according to Command Checksum: Sum of Frame Length, Address Code, Command and Data. (Please pay attention that when the command or data changes, the checksum will change. ) 2 Command Format 2.1 Read angle of X axis Command：77 04 00 01...

Low Cost Single-Axis Digital Output Inclinometer 0x00: absolute zero 0x01: relative zero Command response： Identifier (1byte) 0x00: absolute zero 0xFF: relative zero Note: absolute zero：Based on the factory-calibrated zero point. relative zero: Reference to the zero after the current installation. 0x00: absolute zero 0x01: relative zero 0x00: absolute zero 0xFF: relative zero Command response： Identifier (1byte) Command response： Identifier (1byte) Data （1byte） 0x00: success 0xFF: failure

Low Cost Single-Axis Digital Output Inclinometer Command response： Identifier （1byte） 0x00: question and answer Mode 0x01: 5Hz 0x0C Data Rate Data Data Data Data Data Rate Rate Rate Rate Rate Note: The default output mode is 00(when setting 100HZ output frequency. Set baud rate to 115200 in high speed mode. Command response： Identifier (1byte) 0x00: success 0xFF: failure Note: Set to the response mode, it must receive the read angle command to output the angle. Set to automatic output system, it will automatically output the angle when power is turned on. Command response： Identifier (1byte)...

Low Cost Single-Axis Digital Output Inclinometer Executive standard ● Enterprise Quality System Standard: ISO9001:2008 Standard (Certificate No.10114Q16846ROS) ● CE certification (certificate number: 3854210814) ● RoHS (certificate number: G190930099) Bewis Sensing Technology LLC

BWK216S Low Cost Single-Axis Digital Output Inclinometer Wuxi Bewis Sensing Technology LLC Address: Building 30, No. 58 Xiuxi Road, Binhu District, Wuxi City, Jiangsu Province, China Tel/Whatsapp: +86 189 2129 2620 Email: [email protected] Website: www.bwsensing.com