BWSENSING BWH516
13Pages

Catalog excerpts

BWH516 High Precision Single-Axis Digital Output Inclinometer Technical Manual

High Precision Single-Axis Digital Output Inclinometer Introduction Designed by Bewis Sensing Technology LLC, BWH516 is a single-axis high precision inclinometer with MEMS technology and digital output. It has a measuring range of ± 30° and the highest accuracy of 0.003°. It is a cost-effective product. The product has automatic compensation and filtering algorithms to reduce errors caused by environmental changes. This product adopts the principle of non-contact measurement. It measures the change of static gravitational field and converts it into angle change. The change directly outputs...

Open the catalog to page 2

BWH 516 High Precision Single-Axis Digital Output Inclinometer Resolution: The measured minimum change value that the sensor can detect and resolve within the measurement range. Accuracy: The error between the actual angle and the Root mean square(RMS) of the measured angle of the sensor (>16 times). Bewis SensinglTechnologylLLC

Open the catalog to page 3

High Precision Single-Axis Digital Output Inclinometer Mechanical Characteristic Connector Metal connector Protection level Shell material Magnesium alloy anodizing Package size Product Size：L103.8*W55.4*H26（mm） Bare plate product size Product size: L68*W48*H12(mm) Note: ±1mm error for length and width dimensions, please refer to actual. 63 Bewis Sensing Technology LLC

Open the catalog to page 4

High Precision Single-Axis Digital Output Inclinometer Installation direction The correct installation method can avoid measurement error. The following points should be made when installing the sensor: First of all, to ensure that the sensor mounting surface and the measured surface completely close, the measured surface should be as horizontal as possible, can not have the angle shown in Figure A and Figure C, the correct installation is shown in Figure B and Figure D. B uneven surface generates the angle D uneven surface generates the angle Secondly, the bottom cable of the sensor and...

Open the catalog to page 5

BWH 516 High Precision Single-Axis Digital Output Inclinometer ■•(RED VCC ■•^YELLOW D+ ■•^GREEN D- Electrical interfaces RS 232 wiring diagram Bewis SensinglTechnologylLLCP

Open the catalog to page 6

High Precision Single-Axis Digital Output Inclinometer Debug software Users can directly download serial assistant on official website (Supports-Download). You can also use more convenient and intuitive PC software. BWH516 supporting serial debugging software can be connected to the inclinometer on the computer for angle display. The software debugging interface is as shown in the figure below. Using the debug software, it can conveniently display the current X-direction tilt angle, and you can also modify and set other parameters by yourself. Software use steps: ① Correctly connect the...

Open the catalog to page 7

High Precision Single-Axis Digital Output Inclinometer Protocol 1Data Frame Format：（8 data bits，1 stop bit，No parity check，default baud rate 9600） Identifier （1byte） 0x77 Data Format: Hexadecimal Identifier: Fixed to 77(partly 68) Frame Length: Length from Frame Length to Checksum（included） Address Code: Address of acquiring module, default 0x00 Data: Content and length variable according to Command Checksum: Sum of Frame Length, Address Code, Command and Data. (Please pay attention that when the command or data changes, the checksum will change. ) 2 Command Format: 2.1 Read angle of X...

Open the catalog to page 8

High Precision Single-Axis Digital Output Inclinometer Command response： Identifier （1byte） 0x00: absolute zero 0xFF: relative zero Note: This command refers to whether the zero point reference used in the current state is relative zero or absolute zero. Command response： Identifier （1byte） 0x77 Note：For data, 00: 2400, 01: 4800, 02: 9600, 03: 19200，04: 115200，Default 02:9600. Note：Set baud rate to 115200 in high speed mode. When the Set baud rate command is executed successfully, the command response will be return in the original baud rate a

Open the catalog to page 9

Identifier Frame Length Address Code (Ibyte) (Tbyte) (1byte) Command Data (Ibyte) 0x00: question and answer Mode Checksum (Ibyte) Data Rate Data Rate D ata Ra te D ata Ra te D ata Ra te Data Rate Note: The default output mode is 00(when setting 100HZ output frequency. Set baud rate to 115200 in high speed mode. Command response: Note: If Save setting command is not executed, all setting will be invalid after power off. Bewis SensinglTechnologylLLC

Open the catalog to page 10

High Precision Single-Axis Digital Output Inclinometer Command response： Identifier （1byte） 0x77 Command response： Identifier （1byte）

Open the catalog to page 11

High Precision Single-Axis Digital Output Inclinometer Executive standard ● Enterprise Quality System Standard: ISO9001:2008 Standard (Certificate No.10114Q16846ROS) ● CE certification (certificate number: 3854210814) ● RoHS (certificate number: G190930099) Bewis Sensing Technology LLC

Open the catalog to page 12

BWH516 High Precision Single-Axis Digital Output Inclinometer Wuxi Bewis Sensing Technology LLC Address: Building 30, No. 58 Xiuxi Road, Binhu District, Wuxi City, Jiangsu Province, China Tel/Whatsapp: +86 189 2129 2620 Email: support@bwsensing.com Website: www.bwsensing.com

Open the catalog to page 13

BWSENSING BWH516 13Pages

Catalog excerpts

All Wuxi Bewis Sensing Tecnology LLC catalogs and technical brochures

BWSENSING BWH516
13Pages