Features 2 or 4 digitizing channels 100 or 200 MS/s maximum sampling per channel 16 bits vertical resolution 128 MS to 2 GS on-board acquisition memory 65 or 125 MHz bandwidth Full-size, single-slot PCI card Full-featured front-end, with software control over input ranges, coupling and impedances 32 bits, 66 MHz PCI standard for 200 MB/s transfer to PC memory Ease of integration with External or Reference Clock In and Clock Out, External Trigger In and Trigger Out Programming-free operation with GageScope® oscilloscope software Software Development Kits available for LabVIEW, MATLAB, C/C# • • • • • • • • • • • The Razor family of 16-bit digitizers represents a new generation of high-speed, high-resolution data acquisition cards from GaGe. Razor digitizers offer many powerful advanced features including: APPLICATIONS Radar Design and Test Disk Drive Testing Manufacturing Test Signal Intelligence Lidar Systems Communications Non-Destructive Testing Spectroscopy High-Performance Imaging Ultrasound Test www.gage-applied.com Razor CompuScope 16XX 16-Bit Family of Multi-channel Digitizers for the PCI Bus The GaGe RazorTM family of multi-channel digitizers features up to 4 channels in a single-slot PCI card with up to 200 MS/s sampling per channel, and up to 4 GB of on-board acquisition memory. Combine several Razor cards for up to 32 channels in a single system.PRELIMINARY

A/D SAMPLING Number of Inputs: 2 or 4 Resolution: 16 bits Dynamic Parameters (see Note 1): CS16X1 CS16X2 SNR 74.5 dB 72.2 dB THD -83.7 dB -80.2 dB SINAD 74.2 dB 71.6 dB ENOB (SINAD) 12.0 11.7 SFDR 84.5 dB 84.4 dB Noise Floor -113.3 dB -110.9 dB Maximum Sampling Rate Per Channel (product-dependent): CS16X1: 100 MS/s CS16X2: 200 MS/s Sampling Rates (product-dependent): 200 MS/s, 100 MS/s, 50 MS/s, 25 MS/s, 10 MS/s, 5 MS/s, 2 MS/s, 1 MS/s, 500 kS/s, 200 kS/s, 100 kS/s, 50 kS/s, 20 kS/s, 10 kS/s, 5 kS/s, 2 kS/s, 1 kS/s Connector: SMA Impedance: 1 MW or 50 W; (software-selectable) Coupling: AC or...

TRIGGER OUT Impedance: 50 W compatible Amplitude: 0-2.5 V Connector: SMA INTERNAL CLOCK Accuracy: ±1 ppm (0 to 50°C ambient) EXTERNAL CLOCK Maximum Frequency: Maximum Razor sample rate Minimum Frequency: 10 MHz Signal Level: Minimum 1 V RMS Maximum 2 V RMS Termination Impedance: 50 W Duty Cycle: 50% ±5% Connector: SMA Coupling: AC EXTERNAL REFERENCE The External Reference timebase is used to synchronize the Internal Sampling Clock Frequency: 10 MHz ±1000 ppm; (software-selectable) Signal Level: Minimum 1 V RMS Maximum 2 V RMS Impedance: 50 W Duty Cycle: 50% ±5% Connector: SMA Coupling: AC CLOCK...

www.gage-applied.com Copyright © 2009 Gage Applied Technologies. All rights reserved. 900 N. State St. Lockport, IL 60441-2200 Toll-Free (US and Canada): phone 1-800-567-4243 fax 1-800-780-8411 Direct: phone +1-514-633-7447 fax +1-514-633-0770 Email: [email protected] or our sales distributor forGermany and Austria: WUNTRONIC GmbHHeppstrasse 30Tel. +49 (89) 3133007Fax +49 (89) 3146706 e-mail: wuntronic@wuntronic Date sheet in German: www.wuntronic.com Notes to specifications: 1) Dynamic parameter measurements were done by acquiring a high purity 10 MHz sine wave with an amplitude of 95%...