TN
12Pages

The Next Generation Injection Molding Machine

Injection Unit Screw & Barrel Type Screw Diameter Injection Pressure Holding Pressure Theoretical Injection Volume Injection Rate Screw Stroke Injection Speed Screw Revolution Clamping Unit Clamping Force ton(kN) Distance Between Tie-Bar (H x V) mm Ejector Force ton(kN) Total Heat Capacity kW Electric Motor Power Capacity kW Total Electric Power Capacity kW Machine Dimension (LxWx H) m 1. Theoretical Injection Volume : Screw Dia x Screw Stroke 2. Minium mold size must be over 60% of distance between tie-bar. 3. This data based upon the 60Hz electricity freguency. 4. Specifications can be...

Machine Dimension Stationary platen punching surface Top surface of stationary platen Hopper mounting surface Injection unit moving stroke Installation Diagram Mold Mounting Diagram Tapped hole layout of take-out robot Stationary platen punching surface Mold installation height Ejection start position : 1 Moving platen Stationary platen

Injection Unit Screw & Barrel Type Screw Diameter Injection Pressure Theoretical Injection Volume Injection Rate Screw Stroke Injection Speed Screw Revolution Clamping Unit Clamping Force ton(kN) 220(2157) 220 (2157) Distance Between Tie-Bar (H x V) mm 620 x 560 620 x 560 Ejector Force ton(kN) 5.8(57) 5.8(57) Total Heat Capacity kW 9.0 9.0 Electric Motor Power Capacity kW 25.0 25.0 Total Electric Power Capacity kW 34.0 34.0 Total Oil Reservoir Capacity t 400 400 Machine Dimension (LxWx H) m 6.7x1.6x2.0 6.7x1.6x2.0 Cooling Water Requirement Umm 60 60 1. Theoretical Injection Volume : Screw...

TN 220S (Ejecting during the mold opening) Injection Unit Screw & Barrel Type Screw Diameter Injection Pressure Theoretical Injection Volume Injection Rate Screw Stroke Injection Speed Screw Revolution Clamping Unit Clamping Force ton(kN) 220(2157) 220 (2157) Distance Between Tie-Bar (H x V) mm 620x560 620x560 Ejector Force ton(kN) 5.8(57) 5.8(57) L. Theoretical Injection Volume : Screw Dia x Screw Stroke 2. Minium mold size must be over 60% of distance between tie-bar. 3. This data based upon the 60Hz electricity freguency. 4. Specifications can be changed for improved development without...

Injection Unit Screw & Barrel Type Screw Diameter Injection Pressure Theoretical Injection Volume Shot Weight (PS) Injection Rate Screw Stroke Injection Speed Plasticizing Capacity (PS) Screw Revolution Clamping Unit Clamping Force Distance Between Tie-Bar (H x V) Platen Size (H x V) Opening Stroke Daylight Min. Mold Height Max. Mold Height Ejector Force Ejector Stroke General Total Heat Capacity Electric Motor Power Capacity Total Electric Power Capacity Total Oil Reservoir Capacity Machine Weight Machine Dimension (L x W x H) Cooling Water Requirement 1. Theoretical Injection Volume :...

TN 280S (Ejecting during the mold opening) Injection Unit Screw & Barrel Type Screw Diameter Injection Pressure Theoretical Injection Volume Injection Rate Screw Stroke Injection Speed Screw Revolution Clamping Unit Distance Between Tie-Bar (HxV) mm 670x620 670x620 670x620 670x620 670x620 Total Heat Capacity kW Electric Motor Power Capacity kW Total Electric Power Capacity kW Total Oil Reservoir Capacity i Machine Dimension (LxWxH) m Cooling Water Requirement e/min 1. Theoretical Injection Volume : Screw Dia x Screw Stroke 2. Minium mold size must be over 60% of distance between tie-bar. 3....

TN 220SH (Ejecting & Charging during the mold opening) IH 2.7 Injection Unit Screw & Barrel Type Screw Diameter Injection Pressure Theoretical Injection Volume Shot Weight (PS) Injection Rate Screw Stroke Injection Speed Plasticizing Capacity (PS) Screw Revolution Clamping Unit Clamping Force Distance Between Tie-Bar (H x V) Platen Size (H x V) Opening Stroke Daylight Min. Mold Height Max. Mold Height Ejector Force Ejector Stroke General Total Heat Capacity Electric Motor Power Capacity Charge Motor Power Capacity Total Electric Power Capacity Total Oil Reservoir Capacity Machine Weight...

Hydraulic / Servo / Hybrid TN 280SH (Ejecting & Charging during the mold opening) 1. Theoretical Injection Volume : Screw Dia x Screw Stroke 2. Minium mold size must be over 60% of distance between tie-bar. 3. This data based upon the 60Hz electricity freguency. 4. Specifications can be changed for improved development without prior notice.

Installation Diagram Mold Mounting Diagram Tapped hole layout of take-out robot Stationary platen punching surface Mold installation height Moving platen Stationary platen

Option Lists S : standard O : option X : not applicable Injection Unit 1. Injection process control stage (Speed/Pressure) 10 10 10 2. Holding process control stage (Speed/Pressure) 5 5 5 3. Charging process control stage (Speed/Pressure) 3 3 3 4. Back pressure control stage 3 3 3 5. Suck-back control (Before) S S S 6. Suck-back control (After) S S S 7. Injection position display S S S 8. Injection speed graphic display S S S 9. Injection pressure graphic display S S S 11. Closed-loop of back pressure S S S 12. Cushion amount displays alarm S S S 14. Auto purge circuit S S S 15. Alarm of...

Global Network Poland Mobile : +48-51-321-1177 India Mobile : +91-99-4134-2299 Mobile : +91-81-3073-2845 CHINA Corporation E-mail : pl@wjpim.com E-mail : in@wjpim.com E-mail : my@wjpim.com E-mail : ph@wjpim.com No 18, Moganshan Road, Beilun, Ningbo, China Tel : +86-574-8680-6088 Fax : + 86-574-8686-3594 E-mail : cn@wjpim.com Guangdong Office Tel : +86-769-8352-5307 Fax : +86-769-8282-5030 Suzhou Office Tel : +86-512-6565-0531 Fax : +86-512-6565-0530 Shangdong Office Tel : +86-535-671-2246 Fax : +86-535-671-7313 Tianjin Office Tel : +86-22-2388-2103 Fax : +86-22-2388-2103 Chongqing Office...