Catalogs >
WinSystems, Inc. >
LPM-LX800

LPM-LX800
6Pages

Catalog excerpts

LPM-LX800-G Multifunction SBC with Video and Ethernet WinSystemsCMOS STD BUS, STD BUS FEATURES • AMD Geode™ LX800; x86-compatible CPU • Up to 1GB of SODIMM system SDRAM supported in a 200-pin SODIMM socket • Socket for up to a 16GB Type I or II CompactFlash • STD Bus compliant board • PC-compatible supports Linux, Windows® Embedded, DOS, and other x86-compatible RTOS • High-resolution video controller supports • Simultaneous analog CRT or LCD operation • Supports CRT resolutions up to 1920 x 1440 • Supports panel resolutions up to 1600 x 1200 • Color panels supported with up to 18-bits/pixel • Backlight power supported • Digital Flat Panel and LVDS support • Custom splash screen on start up • 10/100 Mbps Intel 82551ER Ethernet controller • Four asynchronous serial ports with FIFO. All channels support RS-232/422/485 signal levels • 48 bi-directional TTL digital I/O lines • Bi-directional LPT printer port • Four USB 2.0 ports with overcurrent protection • Supports booting from USB • Ultra DMA100 EIDE controller for one or two devices • AC97 audio • Onboard battery plus connector for off-board battery • PC/104 and PC/104-Plus Bus expansion connectors • AT keyboard controller and PS/2 mouse support • Battery backed Real Time Clock • Programmable Watchdog Timer with long time-out period • 8/16-bit STD Bus interface • Extended operating temperature -40°C to +85°C • +5 Volt only operation • RoHS compliant • Extended operating temperature -40°C to +85°C • Replaces WinSystems' MCM/LPM-6117, MCM/ LPM-TX, and MCM/LPM-DX products The LPM-LX800-G is a STD Bus single board computer based upon the AMD Geode™ LX800 MHz CPU. This chip offers Celeron 800MHz-equivalent performance while drawing less than 5 watts of power. Additional features include onboard video, a 10/100 Ethernet port, four serial COM channels, four USB ports, 48 digital I/O lines and the standard AT peripheral feature set all on a single board. It supports I/O expansion options with the STD Bus, PC/104, and PC/104-Plus Bus support for maximum design flexibility and reliability. The board does not require a fan and will operate over an extended temperature range that makes it ideal for rugged applications requiring an STD Bus embedded PC. Its PC software compatibility assures easy program development, and checkout. This RoHS-compliant board is an upgrade for existing WinSystems' STD Bus CPUs as well as replacing Ziatech , Pro-Log, and VersaLogic’s STD Bus Pentium-class high-performance processor cards. Please contact WinSystems' applicat

Open the catalog to page 1

FUNCTIONAL CAPABILITY Processor - The LPM-LX800-G is built with the low power AMD Geode™ LX800MHz 0.9W with 64KB of I-cache, 64KB of D-cache and 128KB of L2 cache. Its 32-bit x86/87 core allows PC compatible software to run. Also, the integrated FPU supports the Intel MMX™ and AMD 3DNow!™ technology instruction sets for increased performance for communications and multimedia applications. The CPU supports a PCI 2.2-compliant 32-bit interface operating at 33MHz. System Controller - An onboard AMD CS5536 contains integrated controllers for audio (AC97), hard disk drive (ATA-6) USB 2.0, and...

Open the catalog to page 2

resolutions up to 1920 x 1440 x 32 bpp at 85Hz for CRTs and 1600 x 1200 for flat panels with a 24-bit interface. CRT Video Interface - The SVGA video output signals are wired to a 14-pin dual-in-line connector at the edge of the board. An optional CBL-234-G-1-1.375 interface cable adapts it to a standard female 15-pin "D-Sub" type connector commonly used for VGA. Simultaneous operation of the CRT and LCD is supported. Flat Panel Display Support - The LPM-LX800-G supports most flat panel display technologies. The board properly sequences the power for logic voltage and the backlight inverter...

Open the catalog to page 3

and then interrupt the host processor notifying it that a change-of-input status has occurred. Transition polarity is programmable and enabled on a bit-by-bit basis. Each line's transition is latched by the event so that even short duration pulses will be recognized. An interrupt ID register is maintained for each line for writing more efficient Interrupt Service Routines. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O points. I/O Connectors - The LPM-LX800-G has the 48 I/O lines connected to two, 50-pin connectors....

Open the catalog to page 4

is reset. This action is critically important in order to detect brownout or power fail conditions. The reset circuit also ensures that the power is nominal before executing a poweron reset. Battery - An onboard 400 mAH battery supplies the LPMLX800-G board with standby power for the real time clock and CMOS setup RAM. The power supervisory circuit senses the off-board voltage and automatically switches to internal power when it drops below normal. There is an optional WinSystems' external battery pack that can be plugged into the LPM-LX800-G. The battery is a 1600mAH 3.6V unit that works...

Open the catalog to page 5

any differences in the boards or new software drivers that may be needed, please contact the factory. Engineering Support - WinSystems provides free technical phone support to assist customers with system integration of our SBCs and I/O modules into your design. Software - The LPM-LX800-G is designed to run both 16-bit and 32-bit x86 instruction set software. It is compatible with Microsoft's Windows XPe and the applications that run on it. It also supports Linux and other PC-compatible x86 operating systems such as DOS, QNX, and VxWorks. It also will run other real-time executives that...

Open the catalog to page 6

LPM-LX800 6Pages

Catalog excerpts

All WinSystems catalogs and technical brochures

LPM-LX800
6Pages