PRODUCT SPECIFICATION

70-75 Series Sockets Sockets WERNER'S 70-75 series sockets are the widest range of relay sockets. They are designed, manufactured and tested to meet the most demanding worldwide standard industrial requirements, our general purpose sockets offer reliable design, compact quick replacements, panel space saving and cost effective solutions. Features Overview Sockets with built in Diodes Sockets with 10 amps contact ratings Sockets with dielectric strength 2000V Options from single pole up to four poles Highlights Suitable for Din rail and PC board mounting Sockets with screw type & plug in type...

70-75 Series Sockets Sockets Features: Dielectric strength 2,000V Compact and small 10A Contact Capacity. Built-in Diode models Overvoltage category III, as per EN IEC 60947-5-1 Approvals Approbations and Declaration of conformity Model Selection Description

70-75 Series Sockets DIN Rail Mounting Without Fingersafe Without Fingersafe 2-04.2 Mounting Holes (or M4 Tapped Holes) 2-04.2 Mounting Hole (M4 screw hole) 2-04.2 Mounting Holes (or M4 Tapped Holes) 2-04.2 Mounting Holes (or M4 Tapped Holes) Terminal Arrangement (i \ _ .2 r^Q-nlo nJ o- |J<3)®—P] a—© fc- _ Terminal Arrangement I r^Q-ni° I1 > D-©

70-75 Series Sockets DIN Rail Mounting 4 Poles Rated Insulation Voltage Rated Current Insulation Resistance Applicable Wire Screw Terminal Screw Tightening Torque Dielectric Strength Operating Temperature Degree of Protection Weight (approx.) Applicable Relay 25 2-ø4.2 Mounting Hole (M4 screw hole) Terminal Arrangement 2-ø4.2 Mounting Hole (M4 screw hole) (cannot use ring terminal) Terminal Arrangement

70-75 Series Sockets PC Board Mounting (Bottom View)

70-75 Series Sockets PC Board Mounting (Bottom View) (Bottom View)

70-75 Series Sockets DIN Rail Mounting

70-75 Series Sockets DIN Rail Mounting

70-75 Series Sockets 2 Poles PC Board Mounting 3 Poles

70-75 Series Sockets DIN Rail Mounting Without Fingersafe Without Fingersafe 2-04.2 Mounting Holes {or M4 Tapped Holes) 2-04.2 Mounting Holes (or M4 Tapped Holes) Terminal Arrangement "§ oIqj-©©I 2-04.2 Mounting Holes (or M4 Tapped Holes) 2-04.2 Mounting Holes (or M4 Tapped Holes) Terminal Arrangement Terminal Arrangement

70-75 Series Sockets DIN Rail Mounting Terminal Arrangement (Top View)

70-75 Series Sockets DIN Rail Mounting Dimensions Dimensions

70-75 Series Sockets DIN Rail Mounting 1 Pole Rated Insulation Voltage Rated Current Insulation Resistance Applicable Wire With Spring Clamp Screw Terminal Screw Tightening Torque Dielectric Strength Operating Temperature Degree of Protection Weight (approx.) Applicable Relay Protection and indication circuit

70-75 Series Sockets DIN Rail Mounting

70-75 Series Sockets DIN Rail Mounting

70-75 Series Sockets PC Board Mounting

70-75 Series Sockets Precautions Applicable Wires 1. Strip the wire insulation 9 to 10mm from the end. 2. Two cable ports are provided for each terminal. 9 to 10mm Marking Instructions Write markings on the 71 series sockets using an oil-based marker on the marking surface. Dimensions Marking Plate Wire Size Wiring Instructions 1. Insert an applicable screwdriver into the square shaped port until the screwdriver tip touches the bottom of the spring, as shown below. 2. The wire port is now open and the screwdriver is auto-held in place. You can release your hand for comfort. Correct Incorrect...

70-75 Series Sockets Terms And Conditions Please read this catalog before purchasing any products. Please consult your WERNER representative for any clarifications or comments. Application Considerations WERNER shall not be responsible for conformity with any regulations, codes or standards that apply to use of the products. WERNER shall provide applicable third party certification documents identifying ratings and limitations of use that apply to the products in case of the customer's request. Prevent use the products for an application involving risk to life or property. Be sure that the WERNER’s...

Werner Elektrik GmbH Dorotheastraße, 2, 27568 Bremerhaven, Germany T: +49 711 - 6740 0552