Catalog excerpts
TECHNICAL HIGHLIGHTS Intuitive operation thanks to Siemens PLC control with touch display To ensure that the electronics are optimally matched to the machine, we design, build and wire our control cabinets ourselves. We only use high-quality components - for example from Siemens or Rittal. Intuitive touch interfaces guarantee quick adjustments. Functions such as setting the ram cycle or stop ensure a high throughput. The built-in overload protection also prevents defects in the machine. Precise cut with high throughput with profiled V rotor The V rotor, specially developed by WEIMA, can be...
Open the catalog to page 2DURABLE ROTOR BEARINGS thanks to offset design A rotor bearing must be robustly designed due to the extreme stresses it is subjected to while it’s in operation. To prevent dust or foreign matter from getting inside it, we have set it apart from the machine frame. This also makes it very maintenance-friendly and easy to access. Safe material feed with load-controlled ram The ram, which moves horizontally back and forth via hydraulics, feeds the material to the rotor. With WEIMA, it can be controlled or cycled automatically depending on the load. If required, of course, it can also be...
Open the catalog to page 3TECHNICAL HIGHLIGHTS Optimally protected hydraulics installed in the machine frame Integrating the sensitive components of a hydraulic system into the machine frame has many advantages. Not only is it protected from dust, dirt and other external influences such as the weather, but it also makes the machine even more compact in its installation. A separate service opening provides easy access for maintenance. CLEAN DISCHARGE OF MATERIAL by suction, screw or conveyor belt Depending on your needs and frame design (elevated machine with conveyor belt cutout or side spout), you have the option...
Open the catalog to page 4SINGLE-SHAFT SHREDDERS IN ACTION WL 8 Discharge by air suction WL 6 S Integration in production line WLK 800 With discharge conveyor belt
Open the catalog to page 5TECHNICAL DATA AND MACHINE CONFIGURATION Technical data single-shaft shredder Rotor length [mm] Rotor speed [rpm] Drive power [kW] Available knife sizes [mm] Fraction size [mm] Exhaust connection [mm] Hopper opening [mm] Length [mm] Width [mm] 1) dependent on cutting circle ) dependent on specific drive configuration 2 3) dependent on drive technology 4) dependent on machine con
Open the catalog to page 6• Standard • Optional Machine configuration single-shaft shredder Segmented floor Hold-down device Fast hydraulics Free-cutting hopper Electromechanical drive Hydrodynamic start-up clutch Additional rotor knife row Adjustable counter knife Vautid rotor wear protection Detached bearings Screw screen Swivel down screen Conveyor belt cutout Exhaust connection
Open the catalog to page 7WEIMA Maschinenbau GmbH | weima.com Bustadt 6–10 | 74360 Ilsfeld (Germany) | Phone: +49 (0)70 62 95 70-0 | Fax: +49 (0)70 62 95 70-92 | info@weima.com Subject to technical changes | 01082021
Open the catalog to page 8All WEIMA Maschinenbau GmbH catalogs and technical brochures
-
WEIMA Single-shaft shredders
76 Pages
-
WL 4 | Single-shaft shredder
8 Pages
-
C series | Briquette presses
8 Pages
-
WL 6 | Single-shaft shredder
8 Pages
-
WL 4 | Single-shaft shredder
8 Pages
-
WL 8 | Single-shaft shredder
8 Pages
-
WL 4 | Single-shaft shredder
8 Pages
-
HD 500 | HD 700K | HD 1500
4 Pages
-
TH 1500 | TH 2800 | TH 3400
5 Pages
-
TH 3400 – Briquette Press
5 Pages
-
C 140 – Briquette Press
4 Pages
-
SPIDER HRS-SERIES
8 Pages
-
Series WSM Granulators
2 Pages
-
WLK
5 Pages
-
Briquetting presses
8 Pages
-
Series WT
2 Pages
-
Granulator
2 Pages
-
Four-shaft shredder
2 Pages