Catalog excerpts
C SERIES BRIQUETTE PRESSES 01 |
Open the catalog to page 1The family business. The young entrepreneur and visionary, Peter Rössler, recognized the potential of waste recycling early on and founded Weinsberg Maschinenfabrik – or WEIMA for short – in 1980. After the turn of the millennium, Martin Friz succeeded in bringing about the generation shift and has now been running the business since 2003. Global leader. WEIMA produces more than 1,200 shredders, briquetters and drainage presses per year on a production area of approx. 65,000 sqm with more than 300 employees worldwide. Since its foundation, about 40,000 machines have been delivered...
Open the catalog to page 3TECHNICAL HIGHLIGHTS Spacious feed hopper as material buffer C Series briquetting presses offer a large capacity for material to be compressed. Depending on the space requirements, the press unit and the hydraulic unit can be flexibly installed to the right or left of the hopper. The agitator and the material screw conveyor are located at the bottom of the hopper. If required, the hopper can be equipped with a fill level monitoring system which automatically switches off the briquette press as soon as the material quantity falls below a defined level. Vertical material pre-compaction in the...
Open the catalog to page 4Proven clamping technology for high-strength, round briquettes up to 70 mm Ø ROBUST HYDRAULICS with separate oil tank The compact hydraulic unit is located directly next to the feed hopper. It is temperature controlled. The pump motor is designed for long service life. The extremely wear-resistant, chromeplated pressing clamp is surrounded by a hydraulic closing cylinder. It holds the briquette produced by the pressing cylinder during pressing. For this purpose, both halves of the clamp are closed and opened again during discharge. Consistent briquette lengths thanks to electromechanical...
Open the catalog to page 5TECHNICAL HIGHLIGHTS Minimal wear in the press chamber due to pressing chamber wear sleeve WEIMA‘s standard pressing chamber wear sleeves are hardened. Optionally, they are made of tool steel. In both cases, increased wear of the press chamber is effectively prevented – especially with abrasive materials containing sand, soil, or metal chips. Instead of replacing the entire press block when wear occurs, only the significantly less expensive pressing chamber needs to be replaced. This saves labor, time, and costs – maintenance is significantly simplified. LOW MAINTENANCE HYDRAULIC CYLINDER...
Open the catalog to page 6TECHNICAL DATA AND MACHINE CONFIGURATION Technical data C series Hydraulic oil volume [liter] Briquette diameter [mm] Throughput rate up to [kg/h] Space requirement (L × W × H) [approx. mm] 1) depending on material ) detailed dimensions upon request 2 Machine configuration C series • Standard • Optional MECHANICS Press mechanics with hydraulic cylinder Briquette length monitoring Pressing chamber wear sleeve Chrome plated clamp Hydraulic power unit with tank Safety switch for oil temperature On-off automatic with level limit switch Inspection cover with limit switch Reinforced agitator...
Open the catalog to page 7WEIMA Maschinenbau GmbH | weima.com Bustadt 6–10 | 74360 Ilsfeld (Germany) | Phone: +49 (0)70 62 95 70-0 | Fax: +49 (0)70 62 95 70-92 | info@weima.com Subject to technical changes | 01082021 | 07
Open the catalog to page 8All WEIMA Maschinenbau GmbH catalogs and technical brochures
-
WEIMA Single-shaft shredders
76 Pages
-
WL 4 | Single-shaft shredder
8 Pages
-
WL 6 | Single-shaft shredder
8 Pages
-
WL 4 | Single-shaft shredder
8 Pages
-
WL 8 | Single-shaft shredder
8 Pages
-
WL 4 | Single-shaft shredder
8 Pages
-
HD 500 | HD 700K | HD 1500
4 Pages
-
TH 1500 | TH 2800 | TH 3400
5 Pages
-
TH 3400 – Briquette Press
5 Pages
-
C 140 – Briquette Press
4 Pages
-
SPIDER HRS-SERIES
8 Pages
-
Series WSM Granulators
2 Pages
-
WLK
5 Pages
-
Briquetting presses
8 Pages
-
Series WT
2 Pages
-
Granulator
2 Pages
-
Four-shaft shredder
2 Pages