Catalogs >
weber Sensors GmbH >
Data sheet flow-captor 4120.1xMA S113 S110

Data sheet flow-captor 4120.1xMA S113 S110
1 / 3Pages

Catalog excerpts

Data sheet flow-captor 4120.1xMA S113 S110 - 1

Flow switch for TRI-CLAMP® System / EHEDG certified flow-captor 4120.1xMA S113/xx S110/xx The flow-captor type 4120.1xMA S113/xx S110/xx is ideally suited for use in automation processes in the food industry where liquid media must be monitored. The sensor was specially designed for Tri-Clamp connections. Application under EHEDG conditions - see additional text. It operates according to the calorimetric measuring principle, fully electronically and without mechanically moving parts. The sensor detects the flow velocity of the medium and converts it into an electrical signal. • • • • • • • • EHEDG certified TYPE EL CLASS I April 2019 precise switching flow monitor high switching accuracy even with lower flows separate setting for set-point and range LED for output status display of flow condition and adjusted switch point via LED chain robust stainless steel design (special potting) ISO 9001:2015 Technical data Type Medium Sensor data Measuring range Medium temperature Ambient temperature Set-point range Pressure Response time Linearity deviation Repeatability Hysteresis Temperature drift Mechanical data Protection class Housing Sensor head Flange dimensions Electrical connection Connection cable (optional) Electrical data ( Electronic unit ) Operating voltage Current consumption Power consumption Switching current Circuit protection Voltage drop Initial operation Elektrischer Ausgang Switching condition with flow < switching point LED Switching condition with flow > switching point LED 1) picture similar 4120.1xMA S113/xx S110/xx water-based 0 - 20 cm/s to 0 - 300 cm/s continuously adjustable -20 °C to +80 °C / -4 °F to 176 °F -20 °C to +70 °C / -4 °F to 158 °F approx. 15 % - 90 % of range setting up to 100 bar 2 sec. - 10 sec., according to range setting < 5 % 1) <2% approx. 10 % <3%/K IP67 stainless steel AISI 303 stainless steel 316L, electropolished D50.5 mm or D64 mm 4-pin M12 plug 2 m PUR cable type 4940, 3 x 0.34 mm² with 4-pin M12 coupling 18 to 30 VDC, incl. residual ripple max. 150 mA (pulsed) approx. 1 W ≤ 400 mA reverse polarity, short circuit and overload < 2.5 V at max. load approx. 10 sec. after connection of power 4120.12MA 4120.13MA energized, switched currentless, not switched off off currentless, not switched energized, switched green green www.captor.de info@captor.de DE-25377 Kollmar, Germany Tel.: +49 (0)4128 - 591· Fax: - 593 Sensors GmbH Strohdeich 32 sales@captor.co.uk Tel.: +44 (1704) - 551684 · Fax: - 551297 Merseyside PR8 4DU, UK 66 Eastbourne Road, Southport Sensors Ltd. Sensors LLC. 4462 Bretton Court, Building 1, Suite 7 Acworth, Georgia 30101, USA Tel.: +1 (770) 592 - 6630 · Fax: - 592 6640 sales@captor.com Technical data subject to a

Open the catalog to page 1

Data sheet flow-captor 4120.1xMA S113 S110 - 2

Flow switch for TRI-CLAMP® System / EHEDG certified flow-captor 4120.1xMA S113/xx S110/xx Connection diagram: www.captor.de info@captor.de DE-25377 Kollmar, Germany Tel.: +49 (0)4128 - 591· Fax: - 593 Sensors GmbH Strohdeich 32 sales@captor.co.uk Tel.: +44 (1704) - 551684 · Fax: - 551297 Merseyside PR8 4DU, UK 66 Eastbourne Road, Southport Sensors Ltd. Sensors LLC. 4462 Bretton Court, Building 1, Suite 7 Acworth, Georgia 30101, USA Tel.: +1 (770) 592 - 6630 · Fax: - 592 6640 sales@captor.com Technical data subject to alteration! Rev. AG 05.05..2

Open the catalog to page 2

Data sheet flow-captor 4120.1xMA S113 S110 - 3

Flow switch for TRI-CLAMP® System / EHEDG certified flow-captor 4120.1xMA S113/xx S110/xx Zusatztext für die Anwendung unter EHEDG - Bedingungen Additional text for the application under EHEDG conditions DIN Klemmstutzen, kurz, DIN 32676 (DN 40 (siehe Zeichnung) oder DN 50) DIN Clamp ferrule, short, DIN 32676 (DN 40 (see drawing)or DN 50) Hinweis für den Einsatz des Sensors nach EHEDG (European Hygienic Engineering and Design Group) Der Sensor ist EHEDG zertifiziert. Diese Zertifizierung gilt NUR bei Verwendung von EHEDG zertifizierten Adaptern und Dichtungen. Zur Vermeidung von Toträumen...

Open the catalog to page 3