Catalogue
134Pages

Safety Instructions Greasing Greasing Recommendations AB-Series PTO Drive Shafts & Components AW-Series PTO Drive Shafts & Components 80° Constant Velocity PTO Drive Shafts & Components PTO Splines, Dimensions & Power Rating Safety Clutches Safety Instructions Safety Clutches Splines & Dimensions

Quality fits. Every time. Introduction 2011 The Weasler Engineering group is one of the world’s leading manufacturers of PTO drive shafts and components for Agricultural and Lawn & Turf machinery. Weasler Engineering BV, based in Wijchen, The Netherlands, is a subsidiary of Weasler Engineering Inc. in West Bend, Wisconsin, USA. Weasler Engineering’s wide range of products feature the German-style shafts (lemon and star profile tubing); the Italian-style shafts (triangular profile tubing) and the North American-style (rectangular, square and splined shafting). Weasler offers the widest range...

Safety Instructions

Safety Instructions Quality fits. Every time. Safety Instructions General: It is not allowed to use the PTO drive shaft without guard, with a damaged guard or without using the restraining members correctly attached. A drive shaft guard restraining system is required in the European Union (EU) countries. Worn or damaged parts have to be replaced with compatible parts. Do not expose guarded parts of the shaft by cutting or enlarging the grease access holes. Do not step on or over a PTO drive shaft. PTO drive shafts and (safety) clutches have to match the power take off and the machine type....

Quality fits. Every time. Restraining members: A drive shaft guard restraining system is required in the European Union (EU) countries. If a chain is the method of restraining the drive shaft guard, the following must be taken into account: Chains must be securely attached to the master shield or the implement, in order to prevent the guard from rotating. Be careful to allow sufficient movement of the shaft in all working and transport positions (Figure E). Damaged chains need to be replaced immediately! Never use the chain to support the PTO drive shaft. If the PTO drive shaft is uncoupled...

Safety Instructions Quality fits. Every time. Minimum and maximum length (profile tubes): Try to obtain the greatest possible overlap on the profile tubes. In its working position, the PTO drive shaft must not be extended by more than half of the profile overlap (Pu) available when fully compressed Lz (Figure H). The minimum overlap should be at least 3 times the diameter of the inner profile tube. Figure H: Pu, Lz Minimum and maximum length (profile tubes): To adjust the length on the profile tubes, place the half shaft next to each other in the shortest working position and mark them...

Quality fits. Every time. Instructions for assembling and disassembling of Easy Lock guards: Clean and grease bearing raceway before the bearing is placed in the groove. Slide guard half over PTO drive shaft insert bearing tabs into the openings Turn the bearing until it engages into the guard. Safety Instructions Safety Instructions Push the Easy Lock clip into position. The bearing and guard are now secu GUARD MUST ROTATE FREELY ON YOKES. TO REMOVE GUARD - Use screwdriver to release Easy Lock clip. Turn the bearings to disengage from the guard and remove guard. GREASE 8hr INSERT THE “S”...

Quality fits. Every time. Weasler Engineering BV, Revision 1.1

Quality fits. Every time. Greasing Recommendations Be certain to follow greasing instructions as identified below* **: Grease the PTO drive shaft with high quality multi-purpose grease every 8 shaft operating hours (unless otherwise specified on the guard). If access holes are available, grease the fittings through the access holes. P-Kit: Standard Cross & Bearing Kit E-Kit: Extended Lubrication Cross & Bearing Kit Caution: replacement parts are not greased Replacement parts must be greased at time of assembly and during use per the greasing recommendations. *Constant high angle...

Quality fits. Every time. Greasing Recommendations Greasing recommendations* 80° European Style constant velocity PTO drive shaft with P-Kits: grease after x hours Greasing Greasing * all greasing intervals are application dependent Greasing recommendations* 80° European Style constant velocity PTO drive shaft with E-kits: grease after x hours * all greasing intervals are application dependent Greasing recommendations* 80° World Wide constant velocity PTO drive shaft with P-Kits: grease after x hours * all greasing intervals are application dependent Weasler Engineering BV, Revision 1.1

Quality fits. Every time. Greasing Recommendations Greasing recommendations* 80° World Wide constant velocity PTO drive shaft with E-Kits: grease after x hours * all greasing intervals are application dependent Greasing recommendations* 80° World Wide constant velocity PTO drive shaft with Extended Lubrication: grease after x hours * all greasing intervals are application dependent Greasing recommendations* cross & bearing kits: grease after x hours * all greasing intervals are application dependent Weasler Engineering BV, Revision 1.1

Quality fits. Every time. Greasing Recommendations Greasing recommendations* Safety Clutches: Greasing Greasing Ratchet clutch: Overrunning clutch: * all greasing intervals are application dependent * all greasing intervals are application dependent grease after x hours Shear Bolt clutch: Friction overrunning clutch: 50 * all greasing intervals are application dependent Weasler Engineering BV, Revision 1.1 * all greasing intervals are application dependent

Quality fits. Every time. Weasler Engineering BV, Revision 1.1

Quality fits. Every time. Merchandisers DISPLAY FOR PTO DRIVE SHAFTS Display (excluding PTO drive shafts) Discription Display for PTO drive shafts excluding PTO drive shafts Display (including PTO drive shafts) Item Number 12101028 Discription Display for PTO drive shafts including 8 PTO drive shafts (see below) PTO drive shaft, AB1-series, 1 3/8-6 QD, 1 3/8-6 QD, Lz: 860mm PTO drive shaft, AB4-series, 1 3/8-6 QD, 1 3/8-6 QD, Lz: 860mm PTO drive shaft, AB6-series, 1 3/8-6 QD, 1 3/8-6 QD, Lz: 1010mm PTO drive shaft, AW10-series, 1 3/8-6 QD, 1 3/8-6 QD, Lz: 860mm PTO drive shaft, AW21-series,...