Catalog excerpts
Content: Order Code Technical Data Profinet Interface Connection Technical Drawing
Open the catalog to page 1Absolute encoders – multiturn Standard mechanical multiturn, optical Sendix 5868 / 5888 (shaft / hollow shaft) The multiturn encoders Sendix 5868 and 5888 with PROFINET interface and optical sensor technology are ideal for use in all applications with PROFINET technology. The encoder supports the isochronous (IRT) mode and is therefore ideal for real-time applications. High rotational speed Temperature range High protection level High shaft load capacity Shock / vibration resistant Reverse polarity protection Optical sensor Surface protection salt spray-tested optional • Ideally suited for...
Open the catalog to page 2mechanical multiturn, optical Sendix 5868 / 5888 (shaft / hollow shaft) Mounting accessory for hollow shaft encoders Dimensions in mm [inch] Cylindrical pin, long for flange with spring element (flange type 1 + 2) with fixing thread Connection technology Order no. Cordset, pre-assembled M12 male connector with external thread for port 1 and port 2, 4-pin K4P2M-S-M12-CAT 2 m [6.56'] M12 female connector with coupling nut for power supply, 4-pin K4P2M-S-M12 Mechanical characteristics Resolution singleturn 1 ... 65535 (16 bit), scalable default: 8192 (13 bit) Number of revolutions (multiturn)...
Open the catalog to page 3Standard mechanical multiturn, optical Sendix 5868 / 5888 (shaft / hollow shaft) PROFINET IO General information about PROFINET IO The PROFINET encoder implements the Encoder Profile 4.1. (according to the specification Encoder Version 4.1 Dec 2008”) It permits scaling and preset values, as well as many other additional parameters to be programmed via the PROFINET-Bus. When switching on, all parameters are loaded from an EEPROM, where they were saved previously to protect them against power-failure, or taken over by the controller in the start-up phase. Position, speed and many other states...
Open the catalog to page 4mechanical multiturn, optical Sendix 5868 / 5888 (shaft / hollow shaft) Dimensions shaft version, with removable bus terminal cover Dimensions in mm [inch] Square flange, EH 63.5 [2.5] Flange type 5 and 7
Open the catalog to page 5mechanical multiturn, optical Sendix 5868 / 5888 (shaft / hollow shaft) Dimensions hollow shaft version (blind hollow shaft), with removable bus terminal cover Dimensions in mm [inch] Flange with spring element, long Flange type 1 and 2 2 Slot spring element recommendation: cylindrical pin DIN 7, 0 4 [0.16] 2 3 x M3, 5.5 [0.22] deep 2 Recommended torque for the clamping ring 0.6 Nm Flange with stator coupling, 0 63 [2.48] Flange type 5 and 6 2 Recommended torque for the clamping ring 0.6 Nm Flange with stator coupling, 0 65 [2.56] Flange type 3 and 4 2 Recommended torque for the clamping...
Open the catalog to page 6All WayCon Positionsmesstechnik GmbH catalogs and technical brochures
-
LVIG SERIES
5 Pages
-
LAS2-TM SERIES
3 Pages
-
LASER SENSORS
8 Pages
-
Linear potentiometers
4 Pages
-
Magnetostrictive transducers
4 Pages
-
Ultrasonic sensors
4 Pages
-
Hydraulic sensors
4 Pages
-
Product overview
12 Pages
-
Capacitive Sensor KS
9 Pages
-
LX Compact Sensor
6 Pages
-
SX300 Hydraulic transducer
8 Pages
-
Linear Potentiometer LMS18
4 Pages
-
Linear Potentiometer LSW
4 Pages
-
Linear Potentiometer LZW2-IP
4 Pages
-
B36 Incremental Encoder
5 Pages
-
SSI Absolute Encoder
9 Pages
-
Laser Sensor LAS-T5
5 Pages
-
Laser Sensor LAM
9 Pages
-
Linear Potentiometer LZW
6 Pages
-
Ultrasonic Sensors UFP, UPA
7 Pages
-
CANopen Absolute Encoder
12 Pages
-
Profibus Absolute Encoder
6 Pages
-
EtherCAT Absolute Encoder
6 Pages
-
Analog Rotary Sensor WP
8 Pages
-
Draw wire sensor HX
10 Pages
-
Long Distance Laser LLD-150
5 Pages
-
Laser Sensor LAV
5 Pages
-
Linear Potentiometer LZW2
4 Pages
-
Linear Potentiometer LZW1
4 Pages
-
Linear Potentiometer LRW1
4 Pages
-
Analog Absolute Encoder M36
7 Pages
-
Laser sensors LAR
4 Pages
-
Draw Wire Sensor SX50
13 Pages
-
Draw Wire Sensor SX80
14 Pages
-
Draw Wire Sensor SX120
14 Pages
-
Linear Potentiometer LRW
5 Pages
-
Hydraulic Transducer SX200
6 Pages
-
Digital Length Gauges
5 Pages
-
Digital Scale DMO
3 Pages
-
Draw Wire Sensor MH120
11 Pages
-
Draw Wire Sensors MH60
9 Pages
-
Draw Wire Sensor FX-HM
4 Pages
-
Draw Wire Sensor ZX
3 Pages
-
Laser Sensor LAH-G1
4 Pages
-
VTS-Box Teach Electronic
3 Pages
-
Analog Magnetic Scales MXAZ
4 Pages
-
Digital Magnetic Scale MXS2
4 Pages
-
SSI Absolut Encoder F36
7 Pages
-
Signal Conditioner PMX-24
4 Pages
-
Analog Absolut Encoder M58
5 Pages
-
Draw wire sensors
8 Pages