Draw Wire Sensor SX80
14Pages

{{requestButtons}}

Catalog excerpts

Draw Wire Sensor SX80 - 1

Series SX80 Key-Features: - Measurement ranges from 1000 to 3000 mm - Analog Output: Potentiometer, 0...10 V, 4...20 mA - Teachable outputs: 0...5 V, 0...10 V, with an additional Open-Collector switching output - Digital Output Incremental: RS422 (TTL), push-pull - Digital Output Absolute: CANopen, SSI, Profibus, EtherCAT, Profinet - Linearity up to ±0.02 % of full scale - Protection class up to IP67 - Temperature range -20...+85 °C (optional -40 °C or + 120 °C) - High dynamics - High interference immunity factor - Customised versions available

Open the catalog to page 1
Draw Wire Sensor SX80 - 2

INTRODUCTION WayCon Positionsmesstechnik GmbH is a manufacturer of high quality draw wire position sensors for industrial use. Due to its small overall size, its short assembly time and its possible customisation, the SX sensor technology is a cost-effective and flexible solution for a wide range of industrial applications. The dynamics of the draw wire transducer allows a high motion speed and acceleration of the measuring target. Its rugged design and high quality makes applications in harsh industrial environments possible. Special instruments are available with mounting service of...

Open the catalog to page 2
Draw Wire Sensor SX80 - 3

11 other ranges on request ELECTRICAL DATA ANALOG OUTPUT Potentiometer 1 kO Output Power supply Recommended cursor current Current consumption max. Power consumption max. Output current Dynamics Resolution Noise Inverse-polarity protection Short-circuit proof Working temperature Temperature coefficient Electromagnetic compatibility (EMC) Circuit 0...5 V, 0...10 V, galvanically isolated, 4 conductors theoretically unlimited, limited by the noise dependent on the quality of the power supply 16 yes --20...+85 °C / optional: -40...+85 °C 0.0079 %/K according to EN 61326-1:2013 V + Signal v...

Open the catalog to page 3
Draw Wire Sensor SX80 - 4

TECHNICAL DATA DIGITAL OUTPUT INCREMENTAL Measurement range 1) ±0.05 (independent of the measurement range) Improved linearity (optional) ±0.02 (independent of the measurement range, only in combination with resolution 10 pulses/mm, or higher) 0.5 / 5 / 10 / 25 (the resolution can be raised by the factor 4 using quadruple edge detection) Selectable resolution Z-Pulse distance Sensor element Incremental-Encoder with optical code disk Output signal A, B and Z pulse (plus inverted pulses /A, /B and /Z) connector output M12 or M23 or radial cable output (PVC, standard length 2 m) Protection...

Open the catalog to page 4
Draw Wire Sensor SX80 - 5

TECHNICAL DATA DIGITAL OUTPUT ABSOLUTE CANopen (WCAN) Measurement range Linearity Sensor element connector output M12, 5 pins, axial (WCAN) or connector output M12, 8 pins, axial (WCANP) Protection class maximum 90 % relative, no condensation see „electrical data“ below Mechanical data extraction force, maximum velocity and maximum acceleration see „Mechanical Data“ [g] 700 to 900, depending on the measurement range aluminium, anodised, spring case PA6 ELECTRICAL DATA DIGITAL OUTPUT ABSOLUTE CANopen (WCAN) CAN specification Communication profile Device profile Encoder, absolute linear; CIA...

Open the catalog to page 5
Draw Wire Sensor SX80 - 6

TECHNICAL DATA DIGITAL OUTPUT ABSOLUTE SSI Measurement range ±0.05 (independent of the measurement range) Resolution scalable (with Software) Standard resolution Maximum resolution Sensor element Multiturn-Absolute-Encoder with optical code disk Power supply Current consumption (no load, at 24 VDC) 10...30 (reverse polarity protection of the power supply) max. 50 Protection class Mechanical data -20...+80 extraction force, maximum velocity and maximum acceleration see „Mechanical Data“ aluminium, anodised, spring case PA6 Special cables needed ELECTRICAL DATA DIGITAL OUTPUT ABSOLUTE...

Open the catalog to page 6
Draw Wire Sensor SX80 - 7

MECHANICAL DATA 11 reduced to 80 % when option IP67 is used TECHNICAL DRAWING ANALOG OUTPUT AND DIGITAL OUTPUT WCAN Measurement range TECHNICAL DRAWING DIGITAL OUTPUT INCREMENTAL Measurement range

Open the catalog to page 7
Draw Wire Sensor SX80 - 8

TECHNICAL DRAWING DIGITAL OUTPUT ABSOLUTE Profibus, Profinet, EtherCAT TECHNICAL DRAWING OPTIONS CHANGED ROPE OUTLET AND CABLE OUTPUT Standard Rope outlet Option K2 Standard for cable / connector Mounting: standard rope outlet, rope outlet sideways top (S1) Mounting: rope outlet sideways bottom (S2), rope outlet bottom (S3) The sensor is usually installed by using the regular mounting plate Sensors with option rope outlet S2 and S3 have a modified base plate: (see technical drawing above). 30 By disassembling the mounting plate, there are 2 x M4 threads in 9,25 the sensor housing for...

Open the catalog to page 8
Draw Wire Sensor SX80 - 9

OPTIONS The following table gives an overview of frequently used options, with which the standard sensors can be equipped. Please pay attention that not all options can be combined. Information on possible combinations can be found in the order codes. Option Changed cable or connector orientation (NOT with analog output) Improved linearity Inverted output signal (analog output only) Description Rope outlet points upwards (see drawing on page 8): Standard: sideways, opposite to the rope outlet K1: at the top K2: sideways, same side as the rope outlet K3: at the bottom Improved linearity 0.02...

Open the catalog to page 9
Draw Wire Sensor SX80 - 10

Draw wire sensors with the analogue output versions 5VT and 10VT are equipped with teachable, internal electronics, called VT-Electronics. The signals provided by the sensor's potentiometer are digitized by the VT-Electronics. This digital information is first processed by the electronics, then transformed back and given out as an analogue output signal 0 to 5 V or 0 to 10 V. The digitization offers two possibilities of adjustment, by which the sensor can be configured individually using the Squeezer: 1. Teaching of the measurement range. After a successful teaching process, the squeezer...

Open the catalog to page 10
Draw Wire Sensor SX80 - 11

ORDER CODE ANALOG OUTPUT SX80 Measurement range [mm] 1000 / 1500 / 2000 / 2500 / 3000 Output signal Potentiometer Voltage Voltage Voltage Current Connection Connector output M12, axial, 4 pins Connector output M12, radial, 4 pins 1) Cable output, axial ²) Version Standard Sensor with options 1) only for measurement ranges 1500, 2500, 3500 mm ²) Length in m (min. 2 m) Examples: KA02 = 2 m, KA05 = 5 m Bold text: standard with shorter lead time Description improved linearity ±0.05 % improved linearity ±0.1 % inverted output signal rope outlet sideways top rope outlet sideways bottom rope...

Open the catalog to page 11

All WayCon Positionsmesstechnik GmbH catalogs and technical brochures

  1. LVIG SERIES

    5 Pages