Manual Valves >Waukesha Cherry-Burrell

45 SPRING CHECK VALVES • Waukesha Cherry-Burrell brand W45 Check Valves are ‘wafer-style', where product flow pushes the valve disc away from the seat. In the absence of forward flow pressure, the electropolished spring returns the disc and holds it closed against the seat. Back flow pressure also pushes the disc into the closed position. • Two available seal options: o-ring or Tri Ring; in the disc OD provides tight closure while metal-to-metal contact between the disc and seat allows for long-lasting, durable operation. • Machined from 316L stainless steel bar with all polished surfaces < 32...

Check Valves 4 5 BY BA L L C H E C K VA LV E S • Waukesha Cherry-Burrell brand Ball Check Valves have a 316L stainless steel body with a curved offset ball trap. Product flow pushes the ball up into the trap and out of the product stream for full diameter flow. • This valve is well suited to applications where there is pulsing flow and should not be used for sticky, adhesive products, or those with excessive viscosities where the ball can be held in the offset tube. • Vertical installations are preferred where product must flow bottom to top to gravity seat the ball. • For horizontal installations,...

62B Air Blow Check Valve 62B AIR BLOW CHECK VALVES • Waukesha Cherry-Burrell brand 62B Air Blow Check Valves are ‘plug-style', where air pressure pushes the bonded rubber plug away from the seat. In the absence of air pressure, the spring returns the plug and holds it closed against the seat. • For 3-A applications the Waukesha Cherry-Burrell brand 62B Air Blow Check Valve must be used with the incorporated filter disc and suitable air to be in contact with product. • Air usage: estimated air volume usage will depend upon the pipeline vessel to be evacuated. The Waukesha Cherry-Burrell brand...

45HMP HORIZONTAL CHECK VALVE • Waukesha Cherry-Burrell brand 45HMP Check Valves are ‘wafer-style', where product flow pushes the valve disc away from the seat. In the absence of forward flow pressure, the electropolished spring returns the disc and holds it closed against the seat. Back flow pressure also pushes the disc into the closed position. • Eccentric design allows free draining when mounted in the horizontal position. *Dimensions shown are for S-Line connection only, for other types of connection dimensions contact factory. FEATURES: • Eccentric body construction for free draining in...

Plug Valves Plug valves have the longest service history of sanitary valves still in common use. They are manually operated and simple and easy to use. Plug Valves consist of a stainless steel body and a conical plug that is rotated in the body to stop or divert the flow. • 10C: 2-Way Plug Valve is used only as a Shutoff Valve • 11C: 3-Way Plug Valve may be used as a divert to change the flow direction or as a Shutoff Valve N o t e : Th i s i s a s p e c i a l f e a t u r e o f t h i s v a l v e a s m o s t D i v e r t Va l v e s c a n n o t b e u s e d a s S h u t o f f Va l v e s . Plug Valves...

2-Way with Metal or Rubber Cover 3-Way with Metal or Rubber Cover Rubber Seat R = Buna Rubber only indicate for rubber seat MP = S-Line Ml = Male 1-Line I = Female 1-Line Q = Q-Line B = Bevel Seat W = Buttweld

*Dimensions shown are for S-Line connection only, for other types of connection dimensions contact factory. Connection MP=S-Line 1= 1-Line Q= Q-Line W= Buttweld nothings Bevel Seat

Relief Valves 16AMP-AR AIR RELIEF VALVES • Compact and mounted in an S-Line Clamp Connection, the 16AMP-AR relieves air/vapor pressure and is most commonly used on the inlet of a Centrifugal Pump so when the pump is operating, the valve is sealed by the low suction pressure. However, when the pump is “air locked,” the pressure increases and the valve opens to let the air out of the system. Comprised of a Nylon poppet valve with a Buna o-ring seal, the valves can be supplied with 304SS, or 316LSS cap bodies. • The valve is supplied in sizes 1.5” - 3” (38 mm - 76 mm).

Relief Valves 4 0 C F - A R A I R V E N T VA LV E S • For installation on pump suction lines, the 40CF-AR Air Vent Valve is designed to operate as a CIP return air relief, and operates against either vacuum or positive pressure. For proper operation, the valve should be mounted vertically. • The 40CF-AR is available in 1.5"-4" (38 mm - 102 mm) sizes. S-Line connections are standard. Other connections are available on request. • The 40CF-AR has a polypropylene ball that acts between the upper and lower machined seats. The valve body is machined stainless steel, either 304 or 316 • Buna gaskets...

K30SA Material 316L Sizes Available: 1.5" (38 mm) or 2" (51 mm) S-Line Inlet Standard FKM Rubber Stem Plug Material 316L Body Styles Available: • Standard Tee • SIP 0.125” ( 0.32 mm) Tube OD Seat Material PTFE Inlet Connections Available: • S-Line Outlet Connections Available: • S-Line (only available with .5" (13 mm) outlet size) • Buttweld • Hose Barb INLET SIZES OUTLET SIZES FEATURES: • 316L SS Wetted Parts Actuation • W30 - Nylon Actuator Knob • K30SA - push button with spring return OPTIONS: Inlet Connection: • W30 - 0.5" (13 mm), 0.75" (19 mm), 1.5" (38 mm), or 2" (51 mm) S-Line • K30SA...

Manual Valves Based in Charlotte, North Carolina, SPX FLOW, Inc. (NYSE: FLOW) is a multi-industry manufacturing leader. For more information, please visit www.spxflow.com S PX F LOW 611 Sugar Creek Road Delavan, WI 53115 P: (262) 728-1900 or (800) 252-5200 F: (262) 728-4904 or (800) 252-5012 E: [email protected] SPX FLOW, Inc. reserves the right to incorporate our latest design and material changes without notice or obligation. Design features, materials of construction and dimensional data, as described in this bulletin, are provided for your information only and should not be relied upon unless...