SMART METERING SMART BUILDING SMART INDUSTRY TORAN’O ATEX zone 1 The TORAN’O ATEX ZONE 1 sensor is used to report status changes, pulse count values and analogue measurements of equipment in an AtEx 1 sensitive zone such as water, gas, electricity or thermal energy meters, mechanical pressure switches, pressure transducers. It allows existing equipment to communicate over a public or private LoRaWAN® network. APPLICATIONS ▪ In explosive atmospheres, read index values from gas, electricity, water or energy meters with pulse output; load curve monitoring. ▪ Detection of leaks, fraud and tear off. ▪ Check the condition of mechanical pressure switches located in sensitive areas. ▪ Associated with a pressure probe, measurements on a gas network. LoRaWAN®, Class A Easy to install and use 3 pulse inputs or status reports 3 analogue inputs: 2x 0-5V and 1x 4-20mA 2 power supply outputs: ~5Vdc and ~16Vdc SAFT LS17500 Lithium battery on holder (IP55 version) Differential data compression IP55 or IP68 Up to 10 years of autonomy Sensors delivered without WATTECO marking CERTIFICATION ▪ RED, UKCA, RoHS ▪ AtEx Zone 1 certification according to marking: - Ex II 2 G - Ex ib IIC T4 Gb - -20 ≤ Tamb ≤ +50°C The TORAN’O ATEX zone 1 sensor allows metering from the pulse output of water, gas, electricity or energy meters to monitor consumptions. The TORAN'O sensor enables all your mechanical pressure switches in AtEx zone 1 explosive atmospheres to communicate with one another and to report state changes. It transforms existing meters into communicating meters via a public or private LoRaWAN® network. Associated with a pressure probe, the TORAN'O AtEx zone 1 sensor allows the pressure information to be transmitted to the LoraWAN® network. Installation and commissioning are quick and easy. The sensor has: - a switch used for its activation and deactivation, - 2 LEDs to monitor the configuration and pairing to the network. Counting data can be stored in the local memory and compressed before being transmitted over the public or private LoRaWAN® network. This reporting technique is particularly suitable for transmitting load curves as it considerably reduces the amount of data transmitted while preserving the autonomy of the sensor. When powered by a SAFT 3.6V/3600mAh Lithium battery, the autonomy of the sensor is 10 years (data compression mode) with a configuration that performs one measurement per day and one transmission per day. Installation, maintenance and operation must be carried out exclusively by a technician qualified for the use of electrical equipment in explosive atmospheres as defined in EN 60079-14. THE LARGEST IOT PRODUCTS RANGE FOR YOUR PROJECT WATTECO is a European leader in the design and manufacture of smart IoT devices to suit all remote reading and data collection solutions. WATTECO is a LoRa Alliance® member since 2015. ©WATTECO - Pôle de Technellys - Bât H, 165 rue de la Montagne du Salut, 56 600 Lanester, France - Tel: +33 2 97 85 67 65 For more information

TORAN’O ATEX zone 1 TECHNICAL DATA RADIOFREQUENCY Measurement periodicity From 10 minutes to 24 hours (configurable) Transmission interval Immediate following measurement or batch at 30min to 48hrs (configurable) Data compression By differential coding (configurable) Activation method Activation by Personalization (ABP) ou Over-The-Air Activation (OTAA) Data encryption Pulse and Status Report INPUTS: intrinsic safety parameters U0 = 18.9V; I0 = 91mA; P0 = 430mW; C0 = 1.6µF [IIB]; C0 = 262nF [IIC]; L0 = 17mH [IIB]; L0 = 4mH [IIC]. 0-5 V INPUTS: intrinsic safety parameters 3.6V / 3600mAh - AtEx...

TORAN’O ATEX zone 1 PRODUCT REFERENCES HS Code TORAN’O ATEX ZONE 1, IP55 - LORAWAN® EU868 TORAN’O ATEX ZONE 1, IP68 - LORAWAN® EU868 Cable - 2 meters with 6-pins Amphenol connector and 6 pins BINDER plug (shunt 3&4 5&6) Cable - 2 meters with 6-pins Amphenol connector and JAE plug (for Gazpar meter) Cable - 2 meters with Amphenol connector to 4 free wires Cable - 2 meters with Amphenol connector to 6 free wires Amphenol connector - 6 pins Amphenol connector - 4 pins ©WATTECO - Pôle de Technellys - Bât H, 165 rue de la Montagne du Salut, 56 600 Lanester, France - Tel: +33 2 97 85 67 65 For more...