IN’O
2Pages

{{requestButtons}}

Catalog excerpts

IN’O - 1

SMART BUILDING SMART INDUSTRY IN’O IN’O is a LoRaWAN® Class A or Class C sensor designed to transform any type of binary I/O sensor into a remote wireless sensor that monitors and controls industrial equipment status. APPLICATIONS  Industry – Process control and automation, power line fault detection.  Water treatment, agricultural irrigation – Monitor and control water valves and pumps, alarm status…  Food production & distribution – Monitor and control cooling equipment, refrigerator door contact status, alarm status…  HVAC & building management – Monitor and control air valves and pumps, heaters/coolers, alarm status, human presence, door contact status, lights… BENEFITS & KEY FEATURES  LoRaWAN®, Class A, Class C  Easy to use and deploy  Simultaneous monitoring and control of up to 10 inputs     and 4 outputs Data compression for batch report Battery operated or external power supply Battery autonomy up to 10 years IP55 Sensors delivered without WATTECO marking The IN’O sensor from nke Watteco is a long range, low power consumption, high performance and high quality LoRaWAN® Class A or Class C device that transforms any type of I/O sensor into a Wireless Sensor. Ten sensors and four actuators can be simultaneously supported by a single LoRaWAN® IN’O device, thus allowing a significant reduction in installation and deployment costs. IN’O is specifically designed for users looking to remotely monitor (ON/OFF status, alarms…) and control (ON/OFF switching) industrial equipment such as pumps, fans, valves, heaters, coolers, motors, generators, lights, doors… The measured parameters can be locally stored, concatenated and compressed. This unique batch mechanism significantly reduces the amount of data transmitted for demanding applications and drastically increases the autonomy up to 10 years when operating on battery. The IN’O sensor can operate either from a 3.6V/3600mAh Lithium battery or from an external 9V-24V/300mW power supply. THE LARGEST IOT PRODUCTS RANGE FOR YOUR PROJECT WATTECO is a European leader in the design and manufacture of smart IoT devices to suit all remote reading and data collection solutions. WATTECO is a LoRa Alliance® member. WATTECO - 6 rue Gutenberg, ZI Kerandré , 56700 Hennebont, France - Tel: +33 2 97 85 67 65 For more infor

Open the catalog to page 1
IN’O - 2

IN’O TECHNICAL DATA RF TRANSCEIVER Frequency (MHz) FIRMWARE Protocol LoRaWAN®, Class A, Class C Transmission cycles Configurable through the network Data history Available Activation by Personalization (ABP) or Over-The-Air Activation (OTAA) AES128 Number of inputs Impedance (MΩ) OUTPUT CHARACTERISTICS Number of Outputs Open Collector POWER SUPPLY Voltage 3.6V / 3600mAh – Lithium battery 9V-24V / 300mW – External power supply 10 years for 1 measurement & 1 transmission per day 3 LEDs for Configuration, Network pairing & Activity on inputs Button / Magnetic Switch Reset, ON/OFF ENVIRONMENT...

Open the catalog to page 2

All WATTECO catalogs and technical brochures

  1. Netw'O

    2 Pages

  2. Inclin'O

    2 Pages

  3. Lev'O+ LPG

    2 Pages

  4. Toran'O

    3 Pages

  5. Press'O+

    2 Pages

  6. Smartplug

    2 Pages

  7. Triphas'O

    2 Pages

  8. Ventil'O

    2 Pages

  9. Move'O

    2 Pages

  10. Temp'O

    2 Pages

  11. Hygrotemp'O

    2 Pages

  12. Pulse Sens'O

    2 Pages

  13. PRESS’O

    2 Pages

  14. Atm'O sensor

    2 Pages

  15. MONIT’O

    2 Pages

  16. INTENS'O

    2 Pages

  17. FLASH'O

    2 Pages