WANGEN KL-R BIO-MIX with X-LIFT

Product catalog summary

Introduction
The WANGEN KL-R BIO-MIX with X-LIFT is a hopper feed pump designed for anaerobic digestion plants. It features the innovative X-LIFT quick change system, which allows for efficient maintenance and reduced downtime.

X-LIFT Quick Change System
The X-LIFT system enables the removal of the rotor, stator, and drive section in just four steps, without removing the pump from its installation position. This system significantly reduces maintenance work and can often be performed by a single person using only four standard tools.

Maintenance Procedure
The maintenance involves four steps: 1) Remove the connecting bolt of the cardan joint to the shaft. 2) Undo the connecting rods on the discharge flange side and remove the flange. 3) Pull the stator and rotor out of the pump housing. 4) Remove the stator from the rotor. This process is facilitated by the FMIP (Full Maintenance in Place) feature, allowing maintenance in confined spaces.

Functionality and Benefits
The X-LIFT system allows the hopper to remain attached during maintenance, eliminating the need to demount piping. This results in shorter downtimes and cost savings. The design ensures pump stability and reliability without additional housing or stator sealing joints, preventing stator leaks.

Certifications
WANGEN PUMPEN is certified under ISO 9001 for quality management, ISO 14001 for environmental management, and ISO 45001 for occupational safety and health protection.

Contact Information
Pumpenfabrik Wangen GmbH, Simoniusstrasse 17, 88239 Wangen im Allgäu, Germany. Technical consultation: +49 7522 997-0, Service hotline: +49 7522 997-997, Spare parts: +49 7522 997-896.

Catalog excerpts

Part of the Atlas Copco Group Hopper feed pump WANGEN KL-R BIO-MIX with X-LIFT The reliable solution, specifically for your anaerobic digestion plant. With the (r)evolution in pump technology: X-LIFT quick change system.

Open the catalog to page 1

WANGEN KL-R BIO-MIX with X-LIFT Rotor/stator removal in just 4 steps The new WANGEN X-LIFT quick change system enables the removal of rotor and stator and the entire drive section (cardan shaft and joints) in just 4 steps. The pump remains in the installation position thus Step 1: Remove the connecting bolt of the cardan joint to shaft. pumps. An additional benefit of the X-LIFT quick change system of the WANGEN KL-R BIO-MIX with X-LIFT is that the maintenance procedure can generally be carried out by a single person, depending on the size of the pump. Changing the complete rotor/stator section...

Open the catalog to page 2

The (r)evolutionary and safe solution Changing of wear parts with very few actions, without removing the pump from the pressure-side pipeline. The WANGEN KL-R BIO-MIX X-LIFT manages this challenge even when there is very little space available thanks to FMIP - Full Maintenance in Place. The innovative X-LIFT quick change system from enormously shorter than with other average pumps WANGEN PUMPEN means that the BIO-MIX and therefore lot of money can be saved. hopper remains attached to the substrate feeding system during changing the rotor/stator. There is The innovative solution of the X-LIFT...

Open the catalog to page 3

Part of the Atlas Copco Group WANGEN PUMPEN is certified to: Nr. E0328 ISO 9001 (Quality management) ISO 14001 (Environmental management) Your contact: Pumpenfabrik Wangen GmbH Simoniusstrasse 17 88239 Wangen im Allgäu Service hotline: Spare parts: © 2023 Pumpenfabrik Wangen GmbH. We reserve the right to error and technical changes ISO 45001 (Occupational safety and health protection)

Open the catalog to page 4

WANGEN KL-R BIO-MIX with X-LIFT

WANGEN KL-R BIO-MIX with X-LIFT

Catalog excerpts

All WANGEN PUMPS catalogs and technical brochures