XL series

Product catalog summary

Description: The document provides technical specifications for the "Single Acting Front Spring" cylinder, part of the XL series. It operates under a pressure range of 1 to 10 bar and a temperature range of 0 to +80°C, with variations for dry air and high-temperature seals. The fluid used is filtered, unlubricated, or continuously lubricated compressed air.

Specifications: The cylinder is available in various versions, including double acting, single acting with front or rear spring, through rod, double push tandem, double stroke tandem, and opposed tandem. Bore sizes range from Ø125 to Ø320, with corresponding port sizes. Standard strokes range from 25 mm to 1000 mm. The cylinders comply with ISO 15552 standards and are interchangeable with ISO 6431/VDMA 24562 standards. They are cushioned as standard and can be equipped with magnetic sensors.

Materials: The end caps are made of painted die-cast aluminum with chromate conversion coating, the cylinder barrel is extruded anodized aluminum alloy, and the tie rods and nuts are steel or stainless steel upon request. The piston rod bearing is bronze-iron, self-lubricating, and the piston is die-cast aluminum alloy with chromate conversion coating. Seals are made of polyurethane and NBR rubber, with Viton® available for certain sizes.

Order Key: The order key includes the cylinder series, bore, version, stroke, series, piston type, and options. Examples are provided for ordering different configurations, including ATEX compliance and stainless steel components.

Technical Data: The document includes detailed dimensions and weights for basic cylinders, through rods, and various tandem configurations. It also provides information on decelerator lengths, maximum strokes, and options for piston rod locking units.

Accessories: A range of accessories is available, including flanges, hinges, clevises, and magnetic sensors. These accessories comply with ISO 15552 standards and are available in various materials, including aluminum and steel.

Low Friction Cylinders: The document describes low friction cylinders in the XT, X, and XL series, used as "dancers" or "enlarger stretchers." These are single acting without a return spring, with various seal configurations for different applications.

Catalog excerpts

Cylinders series "XL" comply with ISO 15552 standard, being In this way completely interchangeable with the former cylinders to ISO 6431 A/DMA 24562 standards. These cylinders are supplied cushioned as standard and, in the version with magnetic piston type can be supplied with magnetic sensors. Available also to directive 94/9/EC ("ATEX" - 2GD category). TECHNICAL DATA Pistone type - Special option H.B.:Magnetic switch FM100-FM157 (see chapter magnetic sensors * See technical data on page 0.12 Cylinder 0125, double acting, 100 mm stroke, non-magnetic piston type, ATEX: 125/100 XL/N/EX Cylinder 0320, through rod, stroke 150, magnetic piston type, stainless steel piston rod: 320R150 XL/M1 / Double acting S Single acting front spring * Y Single acting rear spring * PISTON TYPE T Double push tandem * P Double stroke tandem Z Fit for piston rod locking unit (only 0125) 1 Stainless steel piston rod and rod nut 3 Stainless steel piston rod and rod 5 Extruded profile barrel (only 0125) /EX complies with the ATEX directive "Available even with Viton® seals just for applications where is needed a chemical compatibility; not available for high temperature SPARE PARTS Through rod and polyuretane and NBR rubber 0/SG/R/XL

Open the catalog to page 1

Tie rods cylinders to ISO 1 5552 standard Ø 1 25 ÷ 320 D KK* l l 2* l 8* O PL* SW* TG* VA* VD WB WH* Weight Increase (g) (g) every 1 0mm STANDARDIZED DIMENSIONS P.S.: Rod nuts supplied as standard

Open the catalog to page 2

DOUBLE PUSH TANDEM DOUBLE STROKE TANDEM FIT FOR PISTON ROD LOCKING UNIT

Open the catalog to page 3

Fixings for cylinders Ø 1 25 ÷ 320 to ISO 1 5552 standard FLANGE - STEEL - CPUI/F Ø (supplied with screws) * NOT TO ISO 1 5552 STANDARD FOOT - STEEL - CPUI/PB Ø (supplied with screws) FRONT FEMALE HINGE - NOT TO ISO 1 5552 STANDARD - ALUMINIUM - CPUI/CFA Ø (supplied with screws)

Open the catalog to page 4

Fixings for cylinders Ø 1 25 ÷ 320 to ISO 1 5552 standard REAR FEMALE HINGE (supplied with screws) - ALUMINIUM - CPUI/CF Ø - STEEL - CPUI/CF Ø AC PIVOT FOR REAR FEMALE HINGE (ALUMINIUM) - GALVANIZED STEEL - CPU/CPUI/SEC Ø (STEEL) - GALVANIZED NITRIDED STEEL - CPU/CPUI/SEC Ø AC MALE HINGE (Supplied with screw) - ALUMINIUM - CPUI/CM Ø - STEEL - CPUI/CM Ø AC Ø Weight Weight Alu. (g) Steel (g)

Open the catalog to page 5

Fixings for cylinders Ø 1 25 ÷ 320 to ISO 1 5552 standard SQUARE JOINT NARROW REAR FEMALE HINGE (supplied with screws) - ALUMINIUM - CPUI/CFS Ø - STEEL - CPUI/CFS Ø AC (only for Ø 1 25) L4 XD Weight Weight Alu. (g) Steel (g) NON-ROTATING PIVOT FOR NARROW REAR FEMALE HINGE - GALVANIZED NITRIDED STEEL - CPUI/SEC Ø AT

Open the catalog to page 6

Fixings for cylinders Ø 1 25 ÷ 320 to ISO 1 5552 standard NARROW MALE HINGE WITH ARTICULATED HEAD (ISO 1 2240) (supplied with screws) XD Weight Weight Alu. (g) Steel(g) - ALUMINIUM - CPUI/CMSS Ø - STEEL - CPUI/CMSS Ø AC (only for Ø 1 25) SQUARE JOINT WITH ARTICULATED HEAD (ISO 1 2240) - STEEL - CPUI/ASSS Ø AC Ø CA BQ CK EM G1 G2 G3 H6 JS15 H7 JS14 JS14 1 25 INTERMEDIATE HINGE - STEEL - EXTRUDED TUBE WITH TIE RODS - CX/CPUI/CT Ø (supplied with dowels) SUPPORT FOR INTERMEDIATE HINGE - STEEL - CPUI/SCT Ø

Open the catalog to page 7

Cylinder piston rod attachments Ø 1 25 ÷ 320 FEMALE PISTON ROD CLEVIS WITH PIN AND SNAP RING TO ISO 81 40 - STEEL - M27x2 ÷ M36x2 SELF-LUBRICATING PISTON ROD EYE TO DIN ISO 1 2240 STANDARD - STEEL See chapter magnetic sensors from page 1 .93 of the general catalog (CAT.08/EN) MAGNETIC SENSOR SERIES FM1 00 - FM1 57 FIXING BRACKETS For Ø1 25 ÷ 200 see chapter magnetic sensors from page 1 .93 of the general catalog (CAT.08/EN) SENSOR FIXING BRACKETS - ALUMINIUM - SQ (Supplied with adapter for magnetic sensors series FM1 00)

Open the catalog to page 8

SEALS FOR LOW FRICTION CYLINDERS a) Piston seal for rear chamber; b) Piston seal for front chamber; c) Cushioning seal for rear chamber; d) Cushioning seal for front chamber; e) Rod seal. Rear chamber Rear chamber + cushioning Rear chamber + rod seals Rear chamber + cushioning + rod seals Front chamber Front chamber + cushioning The low friction cylinders series "XT", "X" and "XL" (available from Ø 1 25 to Ø 200), are used as "dancers" or "enlager strechers" cylinders, but they are just single acting cylinders without the return spring. As indicated in the previous table, we can have different...

Open the catalog to page 9