•WINSTA® - The Connection System Full Line Catalog 2011 INNOVATIVE CONNECTIONS

WAGO Registered Trademarks CAGE CLAMP® POWER CAGE CLAMP PUSH WIRE® WAGO trademarks are brand names or territorial registered marks of WAGO Kontakttechnik GmbH & Co. KG

WAGO Full Line Catalog (vói urne 1, Rail-Mounted Terminal Block Systems • Rail-Mounted Terminal Blocks • Modular Connectors (X-COM®-SYSTEM) •Terminal Strips • Patchboard Systems • Shield Connecting System • PUSH WIRE® Connectors for Junction Boxes (vd urne 2, Connectors and PCB Terminal Blocks • Feedthrough Terminal Blocks •MULTI CONNECTION SYSTEM • Specialty Connectors •Wireless Technology, TO-PASS® Telecontrol Technology •Industrial Switches, PERSPECTO •Modular l/O-SYSTEM IP67, Block l/O-SYSTEM IP67 •Sensor/Actuator Boxes IP67, Cables and Connectors IP67 • Power Supplies ( Volume 4, Interface...

Operation of WAGO Connection Technologies CAGE CLAMPÜ The universal connection with "SPECIAL" - Open clamping unit - Release clamp - done! -Terminate both solid and ferruled conductors by simply pushing them in - no operating tool needed. The universal connection for solid, stranded - Open clamping unit - Release clamp - done! CAGE CLAMP®/ The universal connection for conductors larger than - Open clamping unit by turning appropriate hex wrench, or operating tool, counter-clockwise. - Press integrated latch to open clamping unit for hands-free - Insert conductor until it hits backstop. - A small,...

Connectors, Snap-In Device Connectors, Distribution Connectors, Cable Assemblies Linect® T-Connectors, Connectors, Snap-In Device Connectors, PCB Connectors, Distribution Connectors, Cable Assemblies WINSTA® MAXI 831 Series, 5-Pole Cable Assemblies Connectors, Snap-In Device Connectors, Distribution Connectors, Cable Assemblies Supply and Tap-Off Modules for Flat Cables Your Questions - Our Answers Technical Information Approvals - User Guide SEARCH AIDS International WAGO Addresses WINSTA® - The perfect connection!

WINSTA® – A Complete Series Perfects the System. The WINSTA® system forms the electrical interface from power supply and distribution to electrical loads (e.g., lights). It also encompasses data processing (bus lines in building automation). The WINSTA® family: MINI MIDI RD MAXI IDC KNX

WINSTÁ® propels modern buildings to achieve high levels of flexibility and durability that readily satisfy stringent norms and standards. The WINSTÁ® family offers a connection solution for virtually every type of building requirements from power supply to bus lines. Each different WINSTÁ® model has been specifically developed to satisfy pole assignments, installation restrictions Each WINSTÁ® family contains both individual components (such as plugs, sockets, h-distribution connectors, T-distribution connectors, distribution boxes) and cable assemblies in construction- industry standard lengths....

IAÍIKICTA® UIKII /CAGE CLAMPS WINSTA® MINI 890/891 Series Note: - Compact connectors are designed for connection and removal without a load applied. - There is no hazard-inducing interchangeability with systems based on IEC 60309, IEC 60320, IEC 60906 and with national connector and socket systems. - Compliance with the standards does not guarantee hazard-avoiding, non-interchangeability with compact connector systems from various manufacturers. - Compact connector systems are not a substitute for residential connector/socket systems. - WINSTA® MINI connectors are not intended for installation...

1 Handling WINSTA ® 8 Preparation 1. Strip length, outer insulation 2. Strip length 3. Extended ground conductor =  x mm 1 =  9 mm =  8 mm MINI, 890 Series Conductor termination with CAGE CLAMP®S Strain relief mounting To terminate fine-stranded conductors, actuate the clamp via 2.5 mm screwdriver and insert stripped conductor until it hits backstop. Solid conductors can be terminated by simply pushing them in. Latch wired connector onto the base of the strain relief housing. Apply the shield to the rubber cable. Strip length, outer insulation = 30 mm Shield length =  8 mm Push the shield connecting...

S 1 9 1 Push down strain relief clamp by hand. Push down strain relief clamp via 2.5 mm screwdriver alternately on both sides. Latch the top of the strain relief housing. Mounting plate installation Securing the mounting plate via fixing pins. Distributin connector assembly The distribution connectors are latched when mounted on the mounting plate. Locking lever assembly First insert the wired connector into the strain relief housing, then snap the clamp and cover. Marking All products for fixed installations (snap-in versions, distribution connectors) are factory-equipped with locking levers...

1 WINSTA® MINI Sockets and Plugs, 2-Pol< All products for fixed installations (snap-in versions, distribution connectors) are factory-equipped with locking levers to ensure the plugs and sockets are always locked. Additional locking levers are only required for "flying leads" (plug/socket). @ "Certification Agencies" and "User Guide" For coding information, see pages 164 and 165. Fire load upon request!

/CAGE CLAMP®!! WINSTA® - The perfect connection!

1 WINSTA® MINI Snap-In Sockets and Plugs, CAGE CLAMP"!! @ "Certification Agencies" and "User Guide" For coding information, see pages 164 and 165. Fire load upon request!

WINSTA® - The perfect connection!

Conductor ends, bonded: 9 mm Interconnecting cable, socket - plug Connecting cable, socket - free end Connecting cable, plug - free end O "Certification Agencies" and "User Guide Other cables upon request! For coding information, see pages 164 and 165. Fire load upon request! Locking lever, for "flying leads", tool operated Mounting carrier, for "flying leads",