FLUORATED IMMERSION HEATERS CIRCULAR PTFE TANK BOTTOM HEATERS Especially suited for frost protection and made of fluoropolymer, the circular heaters allows heating or maintenance of temperature of corrosive chemical baths in storage tanks. The flexible heating element is fixed to a flexible circular support. This form allows insertion into a tank through a ‘manhole’. Diam 200mm min.with models A to F Diam 500mm .min with models G to K. Circular PTFE heaters offer a simple, economical solution for heating liquids in storage tanks. Made of Teflon® Load 1 W/cm2 , max. temperature 90°C, without gland. Natural convection of stored liquid Important : Types 26458 A to K are supplied without gland (90°C max.) ; other models can be operated up to 100°C when fitted with a sealing gland. Other options on request : single phase or three phase voltage, intermediate powers and loads, cable entry via gland or flange.Teflon® -coated PT 100 probe or TC/J thermocouple positioned on the descending supply cable. Dimensions N and C are tailor made. When ordering state : PTFE immersion heater :Type :Model : - Frame in : PVDF or PP Power (kW) : - Voltage (V) : - Dimension N (mm) : - Dimension C (mm): - Dimension H (mm) : IMPORTANT : Dimension N is the length of cable between the heating element and the connection. It must be long enough for the connector to be clear of vapour. CYLINDRICAL PTFE IMMERSION HEATERS Heating element Storage tank Frame in PVDF PVDF PP PP Polytetrafluoroethylene ( PTFE) is a fluoropolymer.Other polymers with similar composition are know under the Teflon name: Fluorinated ethylenepropylene ( FEP) and perfluoroalkoxy polymer resin ( PFA). They retain the useful properties of PTFE. Polypropylene ( PP) is a thermoplastic polymer. When ordering state : PTFE immersion heater : Type : Model : - Frame in : PVDF or PP Power (kW) : - Voltage (V): Dimension N (mm) : - Dimension C (mm): - Dimension X (mm) Horizontal or vertical fitting. IMPORTANT : Dimension N is the length of cable between the heating element and the connection. It must be long enough for the connector to be clear of vapor. Horizontal fitting Coating FEP PFA FEP PFA Vertical fitting Coating FEP 1 couche PFA 2 couches FEP 1 couche PFA 2 couches Dimensions N, C et X are made to roder Frame in PVDF PVDF PP PP Frame in PVDF PVDF PP PP TEFLON® COATED PT100 PROBES These probes mounted on a holder in PVDF are an essential accessory for the PTFE immersion heaters. Designed to be mounted on the tank edge.They allow to measure the temperature of the heated fluid. Several models are available to fit on different tanks. Connection leads : 1m. Vertical fitting IMPORTANT : The heating area must be covered by at least 20 cm of liquid. Thermocouples or PT100 Teflon coated probes mounted on plonger with a sealing gland in PVDF or in PP. Standard length 0,5 m available up to 5m. Connection leads : 1m. 7 Fluid temperature sensor Website : http://www.vulcanic.com Horizontal fitting RIGID TEMPERATURE PROBES Voltage (V) 230 mono 230 mono 230 mono 230 mono 400 Tri 400 Tri 400 Tri 400 Tri Plonger material PVDF PVDF PVDF PP PP PP Type of probe Pt 100 ohms - 3 wires TC/J TC/K Pt 100 ohms - 3 wires TC/J TC/K E-mail : [email protected]

FLUORATED IMMERSION HEATERS HORIZONTAL OR VERTICAL PTFE IMMERSION HEATERS No Type 26477 26456 26487 26466 Horizontal fitting Coating Frame in FEP PVDF PFA PVDF FEP PP PFA PP Vertical fitting Coating FEP 1 couche PFA 2 couches FEP 1 couche PFA 2 couches Frame in PVDF PVDF PP PP Dimensions N, C and X are made to order : X = height of immersion heater fixing arms on tank edge < height of tank. N = Length of supply cable descending into tank. This dimension must be large enough for the connector to be clear of vapour. C = Length of electric supply cable . The connector must be placed outside the...