Catalog excerpts
LCc-II Load Cell Calibrator FEATURES • Ten calibration registers with 10 point linearization curves • BLH Nobel Quick Cal, 10 point deadload, or 10 point data sheet calibration available for each register • An additional register reads live load cell mV/V • Display “Hold” function • Optional 16 bit analog output configurable for each register • Peak and valley capability for each register APPLICATIONS • Force calibration systems • Dynamometers • Test standards DESCRIPTION The LCc-II load cell calibration indicator uses microprocessor technology to store ten individual, ten point linearized, load cell calibration curves. This capability allows this device to be used as a calibration force measurement indicator with up to ten different load cells. In addition, the LCc is pre-configured at the factory to read actual load cell mV/V outputs for use as a measurement standard with virtually any load cell or other Wheatstone bridge based transducer. For portability, a ruggedized enclosure with transducer selection switch and carry handle is provided. If documentation is required, units have a serial printer communication interface. Hot key displays provide instant access to cell mV/V output, peak, valley, zero, and tare values. To check calibration, three standard values are switch selectable along with a fourth provision for a user supplied resistor. Rear panel tension or compression selection reverses polarity if needed. Signal communication is available in 16 bit analog output and RS-422/485 digital formats. The RS-422 signal can be used for printouts or a full, bi-directional PC interface. When combined with master (NIST calibrated) load cells, the LCc-II becomes a highly accurate system for checking and calibrating other force and weight measurement equipment. Technical contact: blhnobel.usa@vpgsensors.com, Europe: blhnobel.eur@vpgsensors.com, Asia: blhnobel.asia@vpgsensors.com
Open the catalog to page 1LCc-II Load Cell Calibrator SPECIFICATIONS PARAMETER Displayed Resolution Conversion Speed high intensity amber LED display Active Digits 7 digit alpha numeric 0.59 in high for weight 8 digit alpha numeric 0.39 in high for status Displayed Sensitivity 0.4 μV per count (min. tilt. setting) Full Scale Range Dead Load Range Input Impedance Excitation Voltage Linearity PERFORMANCE Resolution REMOTE HOLD INPUT (OPTICALLY ISOLATED) (CONTACT CLOSURE OR DC LOGIC COMPATIBLE) Closed Open Software Filter Step Response normal operation COMMUNICATIONS (STANDARD) Baud Rates full or half duplex ASCII,...
Open the catalog to page 2Legal Disclaimer Notice Vishay Precision Group, Inc. Disclaimer ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE. Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “VPG”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. The product specifications do not expand or otherwise modify VPG’s terms and conditions of purchase, including but not limited to, the warranty expressed therein....
Open the catalog to page 3All Vishay Nobel Transducers catalogs and technical brochures
-
G5 Panel Mount
3 Pages
-
U3SB-A Load Cell
4 Pages
-
T2P1 Canister
3 Pages
-
Web Tension Transducer GLT
4 Pages
-
KIS-1
4 Pages
-
microPOS-4
3 Pages
-
LCT 1008 Load Cell Tester
2 Pages
-
Pocket Calibrator
3 Pages
-
Displacement Transducer
3 Pages
-
LVDT Signal Conditioner
3 Pages
-
Load Beam Transducer
3 Pages
-
High Temperature Load Cell
3 Pages
-
Compression Load Cells
5 Pages
-
Weight Indicator - WIN 3
2 Pages
-
Gateway - GATE 3S
2 Pages
-
Loadcell - KISD-6
2 Pages
-
Transmitter - AST 3IS
2 Pages
-
Transmitter - WST 3
2 Pages
Archived catalogs
-
Web Tension systems
8 Pages
-
Industrial Process weighing
6 Pages