Universal 5 Axis Vise
16Pages

Vischer & Bolli Universal 5 Axis Vise Positive high strength clamping close to the work-piece Obstruction free 5-axis machining

Vischer & Bolli Obstruction free 5-side machining More and more companies are investing in 5 axis machining centres to enable increasingly challenging requirements for more complex work-pieces, shorter run times and smaller batch sizes to be satisfied. Growing importance therefore attaches to the workholding method for which new solutions must be found. The optimal solution for the following key requirements unrestricted all-around access to the work-piece Å optimum clamping height above the table high clamping force 34 kN / 7700 lb Ç, secure clamping by grip jaws with pull-down force É low...

Vischer & Bolli The clamping unit can be mounted directly on T-slot (page 6) or grid machine tables (page 7), grid-plates, pallets or on a base plate (page 5). This base plate includes a number of bores that permit a direct link to the zero point clamping system (vb catalog 7.52) as well as to most T-slot or grid machine tables. The clamping force is generated right below the clamping surface. This completely prevents spreading of the clamping jaws, as can happen if conventional high clamping jaws are used on bed rails with a low mounted spindle. 2 conventional parallel clamping opens under...

Vischer & Bolli Clamping capacity Clamping ra Clamping of larger parts is easily done by joining 2 or more spindles together with the coupling nut part no. 742013. max. tightening clamping force 100 Nm / 80 ft-lb 34 kN / 7700 lb Coupling nut part no. 742013 Spindle setup Secure spindle nut part no. 742008 with set screws part no. 742 SM5x6 on locking slots Locking slot Mount locking nuts part no. 742009 with play, secure with locking screw part no. 742 M6x30 Mounting adapter part no. 742000 Mounting aid for driving sleeve or locking nut Locking slot Driving sleeve part no. 742011, secure...

Vischer & Bolli Set with T-slot baseplate 22 Sample: 742 Set 03 (clamping height 100 mm / 3.937“) – 1 x mounting block (Pos.1 see page 11) – 1 x mounting block (Pos.2 see page 11) – 1 x T-slot baseplate (Pos.10 see page 10) – 1 x spindle 120 mm (4.724“) (Pos.15 see page 4) clamping range 0-120 mm – 2 x grip jaw 8 mm (0,315“) (Pos.22 see page 12) Art. Nr. 742001-63 part no. 742002-63 part no. 742600-T126 part no. 742010-120 part no. 742006-8 clamping height clamping height clamping height clamping height Vise with mounting blocks fixed jaw side part no. 742001-63 moving jaw side part no....

Vischer & Bolli Set to fit T-slot machine table 22 Mounting blocks assembly Sample: 742 Set 30 (clamping height 100 mm / 3.937“) – 1 x mounting block – 1 x mounting block – 2 x key way nut T18-T14 – 8 x shoulder bush Ø16 -Ø12 – 8 x screw M12x45 – 8 x T-nut – 1 x spindle 120 mm (4.724“) clamping range 0-120 mm – 2 x grip jaw 8 mm (0,315“) mounting block part no. 742001-63 part no. 742002-63 part no. 742001-1814 part no. 742001-1612 part no. 742 M12x45 part no. 775-PT06-1412 part no. 742010-120 * matching to machine table (see page 8/9/11 or Check list page 14) moving jaw side Part no....

Vischer & Bolli Set to fit grid machine table Sample: 742 Set 56 clamping height 175 / 6.890“ mounted to off-center-position- grid spacing 50 by brackets with 2 torsion plates and 1 damping plate) – 1 x mounting block – 1 x mounting block – 1 x spindle 120 mm (4.724“) clamping range 0-120 mm – 2 x grip jaw 8 mm (0,315“) – 4 x bracket to grid 50 Ø16 – 8 x shoulder bolt M16 for grid 50 (Pos.1 see page 11) part no. 742001-50 (Pos.2 see page 11) part no. 742002-50 (Pos.15 see page 4) part no. 742010-120 (Pos.22 see page 12) part no. 742006-8 (Pos.29) part no. 742015-50 (Pos.30) part no....

Vischer & Bolli

Pos. Description mounting block fixed jaw for T-slot 63 mounting block fixed jaw for grid 50 / T-slot 100 1 mounting block fixed jaw for grid 40 / T-slot 80 mounting block fixed jaw blank mounting block moving jaw for T-slot 63 mounting block moving jaw for grid 50 / T-slot 100 2 mounting block moving jaw for grid 40 / T-slot 80 mounting block moving jaw blank adapter plate for height 125 3 adapter plate for height 150 adapter plate for height 175 4 fixed jaw torsion plate for height 100 torsion plate for height 125 5 torsion plate for height 150 torsion plate for height 175 damping plate...

Vischer & Bolli T-slot baseplate Matches all common machine-tool tables and 400mm (15.748“) zero point clamping system 4x DockLock 1t plug bore Ø25 (Ø0.984“) vb DockLock spacing 200 ±0.01 (7.874“) = Slot for mounting by brackets part no. 751172 4x DockLock 1t plug bore Ø25 (Ø0.984“) 16x for M16 mounting holes

Vischer & Bolli Mounting blocks Use for: / off-center-position – Grid 40 center-position – T-slot 80 center-position / off-center-position – T-slot 120 off-center-position – Off-center-position-grid 40 Ø12M12 mounted with brackets (Pos.29) Use for: / off-center-position – Grid 50 center-position – T-slot 100 center-position / off-center-position – T-slot 150 off-center-position – Off-center-position-grid 50 Ø16M16 mounted with brackets (Pos.29) fixed jaw side part no. 742001-40 0.4 (Ø fixed jaw side part no. 742001-50 moving jaw side part no. 742002-40 moving jaw side part no. 742002-50...

Vischer & Bolli Jaws Grip jaw, hardened, 5 mm height part no. 742006-4 Soft jaw part no. 742006-R34 (34 mm in height from support plate) Soft jaw part no. 742006-R8 (8 mm in height from support plate) Grip jaw, hardened, 8 mm height part no. 742006-8 Grip jaw round, hardened, 5 mm height part no. 742006-C4 Grip jaw round, hardened, 8 mm height part no. 742006-C8 Workpiece stop Part no. 742 6AWSM (Pos.31) see page 9 80 (3,15“)