8mm, 5mm Proximity Probe TM0180 and TM0105 Systems
8Pages

Proximity Transducers, Seismic Sensors and Accessories 8mm, 5mm Proximity Probe TM0180 and TM0105 Systems Introduction to proximity probe transducers Proximity probe transducers are used to measure the static and dynamic distance between the target and the probe. PVTVM’s TM series proximity probes measure the following:  Radial vibration used for indicating bearing condition and measuring machine malfunctions such as rotor imbalance, misalignment, and shaft crack. Axial thrust position used for determining thrust bearing wear or potential bearing failure. Shaft radial position used for determining shaft position relative to rotor attitude angle, an indicator of rotor stability and shaft alignment. Vibration amplitude and phase angle used for diagnostic information in Polar and Bode formats or for vector monitoring. Eccentricity used to measure the shaft bow during startup of large turbine machinery. Phase reference used for measuring shaft rotation speed and phase angle of shaft vibration for monitoring and diagnostic purposes. The TM series proximity probe systems are designed to meet API 670 standards. Each system consists of a probe, extension cable, and a driver. PVTVM’s transmitters (DTM and TR series) can directly interface with the probe and extension cable; therefore, eliminating the need of a probe driver. This smart design allows for easier field installation and greater economical benefits. Components of proximity probe transducers The TM0180 and TM0105 series probes come in 0.5m and 1.0m cable lengths, as well as, special lengths of 5.0m and 9.0m with an integrated probe and extension cable design. The probe may be selected in English or metric units, as well as, reverse mounting options. Reverse mount probes are used with TM0393 probe housings for hazardous areas. Extension Cable PVTVM’s extension cable design results in better system performance and a longer life cycle. One may select various extension cable lengths based on the probe cable length. The total length of the probe and the extension cable need to be 5m or 9m in total length. The connector on the extension cable is also an API 670 standard, allowing compatibility with other manufacturers’ proximity probe systems. Probe The TM0180 (8mm) and the TM0105 (5mm) probes are designed for long life cycles and are suitable for harsh environments. PVTVM realizes one of the most significant problems in proximity probe installations are ground loops and loss of isolation due to damaged cable jackets. PVTVM’s custom rugged cable jacket prevents the probe cable from breaking and tearing and is highly resistive to corrosive environments. The TM0182 driver is used for the TM0180 and TM0105 proximity probe systems. The circuit isolation from ground is a standard feature for all PVTVM’s drivers. The total length of cable between the probe and the driver should be 5m or 9m. The distance between the driver and the vibration monitor can be up to 300m (1,000 ft). The three conductor shielded cables from the probe driver should be used to connect to a vibration monitor, such as, PVTVM’s PT2060 monitor. The TM0180 probe and extension cable are equipped with a standard protective rubber boot, which covers the connectors and prevents oil and dirt penetration. Note: Probe Driver is not required with some models of DTM or TR Transmitters.

Proximity Transducers, Seismic Sensors and Accessories Hazardous Area System Specifications The TM0180 and TM0105 proximity probe transducers have hazardous area approvals. ATEX: II 1 G,Ex ia IIC T4 Ga@Ta=-55 ℃ to +115℃ II 2 G,Ex ia IIC T2 Gb@Ta=-55 ℃ to +232℃ KEMA07ATEX0110X EN60079-0:2012,EN60079-11:2012,EN60079-26:2007 IECEx:Ex ia IIC T4 Ga IECEx DEK 13.0037 X IEC 60079-0:2011,Ed.6 IEC 60079-11:2011,Ed.6 IEC 60079-26:2006,Ed.2 TR CU: 0Ex ia IIC T4 Ga X № ТС RU C-US. AA87.В.01245 NANIO CCVE ГОСТ 31610.0-2014 (IEC 60079-0:2011) ГОСТ 31610.11-2014 (IEC 60079-11:2011) Power Supply: Voltage:...

Proximity Transducers, Seismic Sensors and Accessories Environmental Probe Driver Temperature: Operation: -40oC to +80oC Storage: -50oC to +100oC Probe Temperature: Operation/Storage: -40oC to +120oC Extension Cable Temperature: Operation/Storage: -40oC to +120oC Humidity: 100% non-condensing Approval: ATEX: Intrinsically safe. Class l, Div. 1, Groups A, B, C and D，T4 Class l, Zone 0, Ex ia llC T4 Non-incendive Class 1, Div. 2, Groups A, B, C and D PCEC: Ex ia IIC T4 TR CU: 0Ex ia IIC T4 Ga X № ТС RU C-US. AA87.В.01245 NANIO CCVE Probe and Cable Approval: ATEX: Class I, Div 1, Grps ABCD, Ex...

Proximity Transducers, Seismic Sensors and Accessories Standard 5mm TM0105 Probes (Works with TM0181 cables and TM0182 drivers) 1/4”-28UNF; armor with FEP jacket Case Length M8×1; armor with FEP jacket Maximum: Case length - 1.0 in Maximum: Case length – 20 mm 7200 Series 5mm TM0105 Probes (Works with TM0181-21747 cables and TM0182-18745 drivers) Probe Type Maximum: Case length - 1.0 in Increment: 01 (10 mm) M8×1; with armor Maximum: Case length – 20 mm

Proximity Transducers, Seismic Sensors and Accessories (Works with TM0181 cables and TM0182 drivers) TM0180 Standard 8mm Probe 3/8”-24UNF; without armor 3/8”-24UNF; with armor 3/8”-24UNF; armor with FEP Unthreaded Length Case Length M10×1; armor with FEP jacket without armor

Proximity Transducers, Seismic Sensors and Accessories Reverse mount M10×1; without Note：-A Driver option is chosen only when the probe TM0180 works with TM0182 driver. When the probe works with other transmitters or monitors, no need to add –A option 7200 Series 8mm TM0180 Probes (Works with TM0181-21747 cables and TM0182-18745 drivers) Probe Type Maximum: Case length - 1.0 in Increment: 01 (10 mm) M10×1; with armor Maximum: Case length - 20 mm without armor

Proximity Transducers, Seismic Sensors and Accessories Extension Cable Extension Cable Extension Cable for 5mm and 8mm Probes (Works with TM0180 probes and TM0182 drivers) Probe Type Cable Length