VETTER High Pressure Leak Sealing System - HLS -
4Pages

SEALI NG LEAKS For accessories, see the end of this chapter from page 88. High-pressure leak sealing system Intelligent hose system for complicated pipe leaks. > Innovation from Vetter > For leaks in pipes with diameter up to 20 cm (8 inch) > Sealing in difficult-to-access places > For counterpressure up to 9 bar (130 psi) Premium set 1500015800 1500019100 (USA) With the premium set, you are equipped for every eventuality. It can be used with several different sized pipes and to seal several leaks at the same time. The set contains 3 sealing plates and can thus be used with a wide range of hazardous materials. 1-4Q (fjlll Sealing hose 1.5 m, 2.5 m, 3.5 m (59 inch, 98 inch, 138 inch) Inflation valve and inflation hose Pressure regulator 200 / 300 bar (2,900 / 4,350 psi) 3 sealing plates NBR, EPDM, FKM, 15 x 21 cm (6 x 8 inch) Bleed valve Transport case 600 x 400 x 220 mm (24 x 16 x 9 inch) In close collaboration with Henkel KGaA, Dusseldorf, Vetter has developed an intelligent sealing hose system. Now you can effortlessly access even hard-to-reach leaks in narrow or unevenly shaped piping systems. The flexible hoses fit perfectly even over complicated leaks, e.g. at T-pieces, pipe bends, connecting branches and welded seams. The hoses are inflated in seconds and withstand counterpressure of up to 9 bar (130.5 psi). Prcise sealing of difficult leaks. In operation 镕 > Can be used on T-pieces, pipe bends or difficult-to-access connecting branches > For leaks in pressure lines or fittings Good reasons: > Universally usable and easy to use > For counterpressure up to 9 bar (130.5 psi) > Additional sealing plates for extra stability > Sealing hoses with electrostatic conductivity (DIN ISO 8031/8.97) Intelligent sealing hose system. E o Q. Guaranteed quality: > Individually tested (with inspection seal) > Earth connection to sealing hose coupling on both sides > All metal parts made of stainless steel .5 <v (0 E V) 3 O "O &- (0 N (0 X Inflated in seconds. 58 59

SEALING LEAKS High-pressure leak sealing system Leak sealing paste The easy way to seal valve connectors and flanges. Basic set 1500019000 The basic set contains 1 hose and 1 sealing plate. The pressure regulator is not included. Sealing hose 2.5 m (98 inch) > Easy to apply > Good rsistance to chemicals > Long-lasting > Up to 0.4 bar (5.8 psi) counterpressure Inflation valve and inflation hose Hard-to-access leaks can be time-consuming to seal. Now there is a quick and easy solution to seal leaks on the smallest valve connectors and flanges. Vetter leak sealing paste reliably withstands...

Inflation - Hazardous material program Accessories - Hazardous material program 0.5 bar (7.25 psi) Inflation with cylinder Inflation hose 0.5 bar (7.25 psi) 5 m (16.4 ft.) 10 m (32 ft.) Controller 0.5 bar (7.25 psi), with fitting control Single controller 0050002201 Compressed air cylinder Dual connector, for simultaneous attachment of 2 compressed air cylinders, thread 5 / 8" 200 bar (2,900 psi) 0050000701 0050001801 1 l / 200 bar, (0.04 cu. ft. / 2,900 psi) steel, 5/8" IT, 200 l (7.1 cu. ft.) 1600010100 0050001501 0050002001 1600008400 Inflation hose, 1 m (3.2 ft.), with bail valve for...

Inflation - Hazardous material program Inflation with alternative air source* Air-supply hose, green Commercially available hand and foot pump Truck tyre valve Compressor Adapter for construction-site compressor Inflation with Vetter hand and foot pump, no further adapters or hoses needed. Hand pump, 520 cc/stroke 1600008700 10 m (32 ft.), with shut-off valve 1600013601 1600008000 4 1600012000 Foot pump, 420 cc / stroke 16000009400 Truck tyre valve connector Adapter for portable compressor 1600008200 Adapter for truck tyre inflation system 1600012900 x0 1600007800 Adapter set for ail...