cad

IsoBlock V-4c
2Pages

{{requestButtons}}

Catalog excerpts

IsoBlock V-4c - 1

IsoBlock V Galvanicaly Isolated Differential Voltage Sensor The IsoBlock V module has been designed to provide high-quality isolated differential voltage measurements for aplications requiring scaling of high voltages, as well as superior isolation. Each IsoBlock V unit hosts four separate isolated channels, each of which can be connected to separate measurement sources while providing a range of functional coverage up to 1500V. The input of each specific IsoBlock channel has its own isolated reference, and can be configured to suit user needs. All processed signals output from the IsoBlock unit are referenced in respect to the ground channel of the user’s data acquisition system. Verivolt designs its IsoBlock V modules with consideration for user great flexibility, high channeldensity and low power consumption. Integrated sensor noise (Referenced to input) Gain (Using 10V standard output voltage) Differential input dynamic range Channels per module Accuracy (percentage of reading) Max total phase shift at 60Hz Max Input delay (120kHz versions) Input-Output non-linearity Integrated channel noise (Referenced to output) Output voltage Gain temperature drift Isolation voltage from primary side to secondary side Withstanding common mode surge voltage Withstanding differential mode surge voltage Connectivity (Connector for power in and signal out to/from the sensor) Outer Dimensions Channels Weight Power Supply Voltage Output type Mechanical Mounting Type Common mode rejection at 60Hz Spring Cage connector 3.9” x 3.5” x 2.5” 1 and 4 channels 198 g (7.0 oz) Output Offset Voltage (Referenced to output) Differential Input impedance Insulation impedance Output impedance HARDWARE DESCRIPTION The IsoBlock V module is designed to isolate and scale down high voltages found in industrial enviroments. The end result is a signal ready to connect to any data acquisition system, while galvanically isolating the source from it. Each channel of the IsoBlock module has a galvanic isolation from the input to the output that can eliminate large common mode voltages. In addition to that, each channel also has a protection stage at the input that guards it from surges. Following the input surge protection stage, there is an amplification stage that brings the input signal to a ±10V range. This signal is modulated into a magnetic field, and then transferred across a galvanic barrier. A demodulating stage recovers the original signal, followed by an anti-aliasing filter and a conditioning stage to output a ±10V differential pair. The figure below shows a block diagram of the process decribed above. < 0.1% < 1.2 mV ±10 V ±50 ppm/°C 112 dB 8V to 28 V Differential pair < ±500 µV > 10 MΩ IsoBlock V single channel block diagram. > 10 GΩ || 2pF 100Ω Environmental Operating temperature Storage temperature - The isolation barrier of every device is tested with a 5 second partial discharge of 1800V for 5 seconds, with a detection threshold of 150pC. - Withstanding common mode surge voltage is 2 seconds half sinewave. - Withstanding differential mode surge voltage is 4 seconds half sinewave.

Open the catalog to page 1
IsoBlock V-4c - 2

MERCHANICAL DIMENSIONS HARDWARE CONFIGURATION A. Connect external power source to power the unit. For proper functioning the power supply should provide a voltage between 8V and 28V with at least 0.25A of continuous current and 0.5A surge during module start-up. B. Securely connect wire in the 20-6 AWG range between the source of measurement and an available IsoBlock’s input screw terminal. C. Securely connect one end of a twisted pair to the output terminals, and the other end to the inputs of your data acquisition unit THIS SENSOR IS NOT A SAFETY DEVICE AND IS NOT INTENDED TO BE USED AS A...

Open the catalog to page 2

All Verivolt catalogs and technical brochures

  1. Entube QE

    2 Pages

  2. Encore

    2 Pages

  3. Entube SE

    2 Pages

  4. V2I

    2 Pages

  5. Entube Z

    2 Pages

  6. Esol TE-MV

    2 Pages

  7. Envoy SC

    2 Pages

  8. Entube DE

    2 Pages

  9. Entube DE-HB

    2 Pages

  10. Entube TE

    2 Pages

  11. IsoBlock C

    2 Pages

  12. IsoBlock Q

    2 Pages