-Telemeasurell Transmitter is available for measuring instruments with Digimatic or RS-232C output. (About other output instruments, please contact with us.) Connector shape of Transmitter varies depending on connecting measuring instrument.-Please check the model by following table.For RS-232C output measuring instrument, connect suitable RS-232C cable to Transmitter(TXG-RS,-RSQ) and the instrument. Telemeasurell General Catalog Transmitter connector shape (photo) •TXG-DS-IMD for IMADA Force gauge DS2(Digimatic Mini DIN 8 Pin) TXG-ZP-IMD for IMAOA Force gauge Z2(RS232C 26 Pin) ^TXG-DDQ has a jack of 03.5 mono-plug connecting Vectrix's hand switch BS-3.5 or Mitutoyo foot switch. * TXG-RS,-RSQ is shipped after setting parameters such as Communication protocol&Data format of measuring instrument and its model. Measuring instruments applied to Telemeasurell Handwriting unnecessary v Only pushing transmission button of transmitter.measured data are input to PC automatically. No more posting error improves reliability of measurement. Wireless input much improves operability Wireless transmission makes free from troublesome output cables. Maximum transmission distance is 50m. Able to receive data from max. 100 measuring instruments with ID No.Easy to set ID No.at hand by data displayed on measuring instrument. ©Multi-point measurement at a time ©Switch Controller (custom order) Transmit measured data of multiple ^^ transmitters sequentially with certain i mV nterval by one button.No power cable by using battery. ©Wireless trigger function Data receiver can transmit trigger signal to maximum 16 Transmitters, then receive measured data from these Transmitters. Supply DC 3V power to OPT RS-232C power supply measuring device. When use transmitter for this device, connect transmitter to the DSUB 9P female connector, then connect measuring device to the □SUB 9P male connector via. RS2332C designated by the device It includes 2 size-AA batteries. Input different measured data into one PC Transmitter automatically converts measured data with different format depended on manufacturer of measurement equipment to common "Telemeasure Format"and sends them to Data Receiver.Software "QC PRO" series can input them to PC and make one Inspection report. Real-time cancel function Canceling latest measured data by Cancel Switch supports prompt amendment of mis-input data. Cost reduction of Inspection division Radical shortening inspection time contributes reduction of labor costs. Transmitter can send measured data every interval from 0.4sec. till 60 mim © By using "QCPRO" or "QCPROMX", OK/NG indication at every ID No. is available by PATLITE. Realized networking by PATLITE.Nearby confirmation of result by every measuring equipment and operator is available.Therefore it is possible to continue inspection work at place where PC screen can not be seen. (PATLITE is separate selling) d 'PATLITE®"is registered trademarks of PATLITE Coorporation. ♦Transmission distance 50m of Telemeasurell is standard value under good view without barrier. Real transmssion distance differs from the distance depending on condition.♦Do not use near medical equipment where malfunction may be caused by radio wave. ©Product,Service,Price and Product name will be changed without notice. @"QC PR0"and "Telemeasure" are registered trademarks of Vectrix Coorporation. ©"Digimatic" is registered trademark of Mitutoyo Corporation. ©Company and Product name in this leaflet are each manufacturer's registered trademark or trademark. "Telemeasure" is wireless equipments which input measured data into PC automatically.lt consists of Transmitter connected with digital measuring instrument and of Oata receiver connected with PC. Software"QC PRO" can prompt make Inspection report and various Quality control charts such as Histogram.

Telemeasure n Data Receiver <Data Receiver : DR-200U/R/D> Use of Specified Low Power 2.4GHz band enabled max. 50m transmission and realized stable communication. •Strengthen collision avoidance of radio wave Designed to avoid radio interference among wireless LAN or Bluetooth equipments. • 128 DR-200U's can be used at same time. 12,800 measuring instruments can be used at the same time. (128 channels of wave form x 100 kinds of Transmitter ID No.) •Two-way communication It is possible to set two-way communication between Transmitter and Data Receiver. Wireless trigger from Data Receiver and data...