AE50i
4Pages

Catalog excerpts

ADCA AUTOMATIC AIR AND GAS VENTS FOR LIQUID SYSTEMS AE50i (Stainless steel 1/2" x 1/2" to 1" x 1/2"; DN 15 x 1/2" to DN 25 x 1/2") DESCRIPTION The AE50 range of automatic vents are designed to remove air or gases from water and other liquid systems, without requiring any external source of energy. They are capable of handling significant loads during start-up while still being able to discharge smaller loads in continuous modulating operation with one single orifice. These ball float type vents are manufactured in stainless steel, available with soft sealing, and can be used in combination with other air elimination and separation systems or directly applied at high points in the pipelines. MAIN FEATURES Suitable for start-up and continuous operation with one single orifice. Allow fast and easy inline maintenance. Corrosion resistant internal parts. No balancing pipe required. OPTIONS: Different soft sealing options. Metal to metal sealing. Cold, hot and superheated water or other liquids compatible with the construction. AVAILABLE MODELS: Female threaded ISO 7 Rp or NPT. Flanged EN 1092-1 PN 40. Flanged ASME B16.5 Class 150 or 300. Vertical installation. It must be installed absolutely vertically at the points in the plant where the air tends to collect. The drain should be piped to a safe location. See IMI – Installation and maintenance instructions. CE MARKING – GROUP 2 (PED – European Directive) PN 40 BODY LIMITING CONDITIONS FLANGED PN 40 / CLASS 300 ALLOW. PRESS. FLANGED CLASS 150 * ALLOW. PRESS. RELATED TEMP. PMO – Maximum operating pressure: 30 bar. TMO – Maximum operating temperature: Metal to metal sealing: 250 ºC; EPDM valve sealing: 130 ºC; FPM / Viton valve sealing: 200 ºC. Min. liquid specific weight: 0,75 kg/dm³. * According to EN 1759-1:2004. Body limiting conditions PN 40 or below, depending on the type of connection adopted. Rating PN 40 for threaded versions. VALSTEAM ADCA We reserve the right to change the design and material of this product without notice.

Open the catalog to page 1

ADCA FLOW RATE CAPACITY (NL/min) MODEL AE50i Values shown refer to capacities of air discharge at 15 ºC, under average atmospheric pressure (1013 mbar). If the temperature of the air differs from 15 ºC, the discharge capacity can be corrected by multiplying it by: temperature in ºC. It may be assumed that the temperature of the air is equal to the temperature of the water. Remarks: As standard, in versions with EN flanged or female Rp threaded inlets, the outlet is female threaded ISO 228. In versions with ASME flanged or female NPT threaded inlets, the outlet is female threaded NPT....

Open the catalog to page 2

Mechanism support AISI 316 / 1.4401; EPDM; Viton Stainless steel / Graphite * Available spare parts; ** Not applicable in NPT version. FLOW DIRECTION VF - Vertical inlet / straight front outlet VALSTEAM ADCA VT - Vertical from bottom to top We reserve the right to change the design and material of this product without notice.

Open the catalog to page 3

ADCA ORDERING CODES AE50i Model AE50i – stainless steel Differential pressure 30 bar Valve sealing Metal to metal None Flow direction Vertical inlet / straight front outlet Vertical from bottom to top Outlet pipe connection Female threaded ISO 228 1/2” Inlet pipe connection Female threaded ISO 7 Rp Flanged ASME B16.5 Class 150 Flanged ASME B16.5 Class 300 Inlet size 1/2” or DN 15 1” or DN 25 Special valves / Extras Full description or additional codes have to be added in case of a non-standard combination VALSTEAM ADCA We reserve the right to change the design and material of this product...

Open the catalog to page 4

AE50i 4Pages

Catalog excerpts

All VALSTEAM ADCA Engineering S.A. catalogs and technical brochures

AE50i
4Pages