u TENSORAPID 5-C The strength measurement system Technical Data

USTER  TENSORAPID 5-C The strength measurement system ® Tensile testing and analyzing instrument for the yarn quality assurance of a wide variety of yarns and fabrics. of the USTER ® TENSORAPID  5 -C installation Basic installation 7 Unwinding device (no illustration) 8 Special clamps 180 ° with booster (no illustration) 9 Reductions clamps (no illustration) 10 Vibration suppressor (no illustration) 1 Test unit – Sensor for force and elongation – Sensor for temperature and humidity 2 Clamping device 3 Finger tensioner 4 Control units 5 Table with touchscreen 6 Calibration device ISOINSPECT (no...

USTER  TENSORAPID 5-C The strength measurement system ® Basic installation Functions – Measurement of tensile strength and elongation of a extensive range of yarns and fabrics – Measurement of the force and the elongation at the first filament break, various modulus values, yield point, natural draw ratio – Analyze evaluation and storage of measurement values – Automatic check of all measured values – Editor for customizing reports and setting of mill limits – Smart view focusing on exception and outliers – Filter functions for quick data selection and for the preparation of long-term reports...

Elongation measuring arrangement Clamp speed Pre-tension Test lengths Elongation measuring range Yarn changer Yarn clamps Control unit (2) Computer software Computer hardware Computer accessories - Electronic elongation measurement - Measuring accuracy for force and elongation measurement: For force ± 1 % (above 100 cN) or ± 1 cN (below 100 cN) and for elongation measurement: ±1 % Continuously adjustable between 50 and 5 000 mm/min Adjustable between 0.5 and 6 000 cN - With horizontal position of clamps: continuously adjustable between 200 and 1 000 mm - With vertical position of clamps: continuously...

USTER  TENSORAPID 5-C The strength measurement system ® Options Reduction clamps (9 ) Application range 180 ° clamps with booster (8 ) Application range – Automatic testing of high strength yarns (e.g. aramides), technical yarns and oiled, high strength ply yarns – Testing of difficult materials which in spite of extensive trials with different clamp inserts and a force reduction over 90 ° reduction curve have so far produced incorrect measurements as a result of slippage or clamp breaks – Special clamps with a force reduction over 180 ° – Pressure doubler Application range Allows quick sample...

USTER  TENSORAPID 5-C The strength measurement system ® Application Software Live view report during the measurement – Analysis tool with all measured data and graphical output – Smart view report for exceptions and outliers – Automatic printout possibility after the measurement Setting of customized limits according to the USTER ® STATISTICS , standard deviation, relative and absolute values – Automatic verfication of the measured value – Measured values which will exceed the limit will be marked with red or purple color in the report Time from the start of measurement to the break of the sample...

USTER  TENSORAPID 5-C The strength measurement system ® Force value at a defined decrease in force Elongation value at a defined decrease in elongation Statistical values – Mean value – Standard deviation s – Coefficient of variation (CV ) – Q95  % confidence interval – Minimum value – Maximum value Graphic output of results Stroke diagram Available for breaking force or tenacity and elongation or tenacity and elongation Available for force and elongation or for other results configurable Force/ elongation diagram – Show all single measurements in curves – Easier detection of the sample due to...

USTER  TENSORAPID 5-C The strength measurement system ® General General ambient conditions Room climate The ambient conditions must be maintained in order to avoid any influencing of the test material according to ISO 139 ( 2015 ) – Humidity: 65 +/- 4  % – Temperature: 20 +/- 2 ° standard atmosphere Installation data Electrical connection Single-phase mains with protective conductor Nominal voltages Mains frequency Power consumption – Air quality: according to ISO 8573 .1, class 3 – Min. pressure at inlet of air filter regulator: 6 bar – Max. pressure at inlet of air filter regulator: 7 bar –...

USTER  TENSORAPID 5-C The strength measurement system ® Space required for the USTER®  TENSORAPID 5-C

Uster Technologies has made all possible efforts to ensure that all information is accurate at the time of publication. Hereby it is declared that alterations to the product may be possible at any time. In these cases the information contained in this technical datasheet is subject to change without notice. October 2017 USTER Switzerland 10.17/© Copyright 20 17 by Uster Technologies AG Adana, Turkey Suzhou, China •• Shanghai, China Coimbatore, India