Group: AMETEK
Catalog excerpts
Product Data TEMPERATURE PRODUCTS Model TW-STEP General Use Thermowells DESCRIPTION U.S. Gauge recommends the use of a thermowell in conjunction with a bimetallic thermometer when the application involves a corrosive medium, high pressure, or high flow velocity. Some specific uses include protection for unarmored liquid-in-glass test thermometers or other temperature sensing elements with a maximum diameter of .25". LENGTHS: ±1/16" on lengths 12" or less; ±1/8" on lengths 12" or over These #20 gauge bimetallic thermowells meet or exceed SAMA specifications and are also available in heavy duty, flange, socket weld, and Van Stone models. Standard thermowells are stepped to 1/2" OD, except for 2-1/2" insertion. Straight shank models are also available. BORE ID: +.005; -.003; usually within ±.002 The standard process connection sizes are 1/2-14 NPT and 3/4-14 NPT, with other sizes available. Materials of construction include 316L stainless steel (standard), 304 stainless steel, and brass (ASTM B-16). A cap and chain for keeping the thermowell bore clean when not in use are available upon request. WELLS 30" AND OVER: Solid bored type will be drilled thru end, plugged, and heli-arc welded; built-up design must be specified beyond 42-1/4" overall length OD TOLERANCES: Fractional: ±.015; Decimal: ±.005 on .000 place; ±.01 on .00 place END THICKNESS: Gun drill bottom; 1/4" to bottom ±1/16"; 3/16" minimum end thickness CONCENTRICITY OF BORE TO OD: ±10% of minimum wall thickness WETTED SURFACES FINISH: Standard finish 60-100 Ra; 16-32 Ra available; 4-10 Ra mirror polish available RADIUS UNDER THREADS AND FLANGES: 1/8" is standard, ±1/16".; 1/16" on Van Stone type MALE THREADS (NPT): ±1 turn on thread gage FEMALE THREADS: 1/2" NPSM standard; 1/2-14 NPT available upon request; go gauge to 5/8" depth of thread; no go gauge 2 turns maximum END OF WELLS: Break corners; no burrs LAGGING EXT.: On screwed wells; left as hex stock (not turned); exception – when hex is not available in special materials STAMPING: Stamped onto hex or round facing open end of well; material code identification; tag numbers Model TW-STEP FLANGED WELLS: Made in accordance with ANSI B16.5; raised face is serrated 125 Ra; smooth face must be specified on order if needed FRONT J: Groove welds are 1/4" wide by 1/4" deep; welds are machined, leaving 1/8" radius; rear welds are 1/8" wide by 1/8" deep V; welds are machined, leaving 1/4" radius; full penetration welds are available upon request and must be specified Dimensions Model Process Connection Shank Diameter Q INCHES (MM) 1.75 (44.5) U = INSERTION LENGTH 1.0 (25.4) THREAD ALLOWANCE On-line order fax: +1 215-323-9450 or e-mail: usg.sales@ametek.com Sales/Technical Support: +1 215-293-4100 | 205 Keith Valley Road | Horsham PA 19044 U.S.A. © 2013, by AMETEK, Inc. All rights reserved. Printed in the U.S.A. PDF513 (160174) Specifications are subject to change without notice. Visit our Web site for the most up-to-date information.
Open the catalog to page 1Product Data TEMPERATURE PRODUCTS Model TW-STEP General Use Thermowells Spec Number Selection Chart Model TW – General Use Model TW – Lagging Extension Model TW – General Use, Heavy Duty Model TW – Lagging Extension, Heavy Duty Model TW – Limited Space 2-1/2" Stem Length Spec No. On-line order fax: +1 215-323-9450 or e-mail: usg.sales@ametek.com Sales/Technical Support: +1 215-293-4100 | 205 Keith Valley Road | Horsham PA 19044 U.S.A. © 2013, by AMETEK, Inc. All rights reserved. Printed in the U.S.A. PDF513 (160174) Specifications are subject to change without notice. Visit our Web site for...
Open the catalog to page 2All U.S. GAUGE catalogs and technical brochures
-
Model V534 Canners Gauge
1 Pages
-
1980
2 Pages
-
1986
3 Pages
-
Product Selection Guide
12 Pages
-
Model 8300EX
2 Pages
-
Model-HPT-100
4 Pages
-
Model-40
9 Pages
-
Model_40_Sales_Flyer_001
2 Pages
-
Model 575-P
4 Pages
-
Model 575
5 Pages
-
Model SDT
4 Pages
-
Model DDMC
9 Pages
-
PMT-LMA-Datasheet
3 Pages
-
Sta-Kool-Cooling-Element
2 Pages
-
Model-ECPT10
2 Pages
-
Model-PST360
2 Pages
-
Model-851
4 Pages
-
Model 831
4 Pages
-
IDT
5 Pages
-
Type-SMJ-and-SNJ-Series
2 Pages
-
Type-SF-Series
1 Pages
-
Type-SCE-Series
1 Pages
-
Type S Series
2 Pages
-
Type-R-Series
2 Pages
-
656
5 Pages
-
571
1 Pages
-
DT
4 Pages
-
POC
1 Pages
-
BAC
2 Pages
-
ADJ
2 Pages
-
P562
1 Pages
-
P844U
3 Pages
-
P915
1 Pages
-
P500
2 Pages
-
1901
2 Pages
-
1535
2 Pages
-
1409
2 Pages
Archived catalogs
-
XR
2 Pages
-
Model TW-STEP Thermowells
2 Pages
-
SOLFRUNT 656 Series Gauges
6 Pages
-
SOLFRUNT 659 Series Gauges
5 Pages
-
SOLFRUNT 1900 Series Gauges
17 Pages
-
1300 Series Receiver Gauges
4 Pages
-
1400 Series Test Gauges
3 Pages