Catalogs >
U.S. GAUGE >
Model 575

Model 575
5Pages

Catalog excerpts

Product Data ELECTRONIC PRESSURE MEASUREMENT PRODUCTS Model 575 Series Submersible Level Transmitters DESCRIPTION The Model 575 is used in general water/wastewater applications. The transmitter is offered in a standard non-clogging snub nose end, flush diaphragm or protected flush diaphragm with flange base for sewage or sludge type media. The 575 series is CSA approved for intrinsically safe operation when used with an approved safety barrier. ●● Low cost measurement solution, easy installation The sensor is designed to provide the convenience of direct submergence in many types of liquids for quick, accurate and reliable measurement. With stainless steel isolation diaphragm (standard) and all 316 stainless steel housing, these solid state instruments provide long lasting service with virtually no maintenance. and precision accuracy ●● Rugged 316 stainless steel construction and wetted materials resists the corrosive effects of caustic medias with excellent environmental protection, designed for continuous submersion ●● 2 wire, 4 to 20 mA output ●● Reverse polarity and surge protected with additional lightning and surge protectors as well as EMI protection options ●● CSA approved for intrinsically safe operation in hazardous areas in Canada and U.S. The 575 Series transmitters indicate the level of liquid by continuously measuring hydrostatic pressure via its sensing element, an ion implanted silicon semiconductor chip with integral Wheatstone bridge circuit. The pressure measurement is transmitted by a 4-20 mA output signal. This design, with isolation diaphragm for media compatibility, provides for excellent linearity and repeatability, low hysteresis and long term stability with a precision accuracy at ±0.25% FS (BFSL) typical. ●● Full potting option and desiccant available The transmitter is easy to install. Simply lower the unit into a tank or vessel. All electronics are mounted in the submersible 316 stainless steel housing and full potting is also provided as an option. A special cable support bracket is also available to provide extra stability when used with longer cable lengths or when used in an agitated liquid. Optional steel support cable is also available for use with the support bracket. to minimize moisture effects APPLICATIONS ●● Inventory tank measurement ●● Ponds, rivers and lakes ●● Lift stations and slurries or sludge ●● Water wells ●● Landfills ●● Pump Model 575P protected flush diaphragm Model 575P protected flush diaphragm with optional 3/4" plate The transmitters are available calibrated for any span needed from 0-6 psi (0-13.8 ft of water, 0-.4 bar, 0-4.2 meters of water) to 300 psi (0-692 ft of water, 0-20 bar, 0-211 meters of water). The transducer is offered as a standard 2 wire, 4-20 mA device. To complete your liquid measurement and control system, consider the Model DDMC meter/controller or the complete Levelmate III system. The 575 transducer is manufactured in the United States under ISO 9001:2008 and meets ARRA. Model 575S standard 1/2 NPT (with nose cone removed) Sales/Technical Support Telephone: +1 215-355-6900 or e-mail: mctpmt.sales@ametek.com 820 Pennsylvania Boulevard | Feasterville, PA 19053 U.S.A. | Order Fax: +1 215-354-1802 © 2015, by AMETEK, Inc. All rights reserved. Printed in the U.S.A. K7946422 – Effective: 6-2015, Supersedes: New (110132) Specifications are subject to change without notice. Visit our Web site fo

Open the catalog to page 1

Product Data ELECTRONIC PRESSURE MEASUREMENT PRODUCTS Model 575 Series Submersible Level Transmitters SPECIFICATIONS Feet of Water: 0/14, 0/35, 0/69, 0/138, 0/230, 0/345, 0/460, 0/690 Cable Jacket: Polyurethane (standard) Electrical Connection: Attached 20 gauge polyurethane shielded cable (standard); unspliced lengths available up to 5000 ft. (1662 m) Consult control drawing or contact the factory for cable length limits for Intrinsically Safe (I.S.) use. Output: 4 to 20 mA, 2 wire, current limited to 30 mA DC Power Supply: 12 to 40 VDC with reverse polarity surge protection; limited to 28...

Open the catalog to page 2

Product Data ELECTRONIC PRESSURE MEASUREMENT PRODUCTS Submersible Level Transmitters Flush Diaphragm RLUSH DIAPHRAGM :AELE LENGTh Transmitter With In Line Desiccant Option For Use With Vent Tube Cables Part #K234436 (original assembly desiccant with hardware] Part #K234446 (replacement cartridge ONLY - requires some assembly of parts from original assembly] Optional Conduit PLUG IS INSTALLED IN COUPLING a) WITHOUT ft GASKET TO PREVENT DISTORTION WHILE WELDING COUPLING b) WITH A GASKET TD SEAL COUPLING FLUSH DIAPHRAGM Optional Cable Support Bracket With Nut and Cable Sales/Technical Support...

Open the catalog to page 3

Product Data ELECTRONIC PRESSURE MEASUREMENT PRODUCTS Model 575 Series Submersible Level Transmitters Model Numbering: 575 level transmitter 575 Series submersible level transmitter Sensing port S Nylon snub nose (standard) M Stainless steel snub nose F Flushmount P Protected flush Reference equivalents 0-13.8 ft. water 0-34.6 ft. water 0-69.2 ft. water 0-138 ft. water 0-230 ft. water 0-345 ft. water 0-460 ft. water 0-690 ft. water 0-4.2 meters water 0-10.5 meters water 0-21.1 meters water 0-42.2 meters water 0-70.3 meters water 0-105.4 meters water 0-140.6 meters water 0-211 meters water...

Open the catalog to page 4

Product Data OPTIONS AND ACCESSORIES Display Meters, Surge Protectors, Junction Boxes and Desiccants DISPLAY METERS AND SYSTEMS Model DDMC Digital Meter/Controller JUNCTION BOXES Model SBJ100 with Reusable Desiccant Dual display meter provides power to the sensor with alarm and 4-20 mA analog output options. Standard panel mount housing or a NEMA 4X weathertight housing for field mounting is available. The weathertight housing also provides internal mounting locations for lightning and surge protectors. These boxes are used on long cable runs and provide quicker access to atmospheric...

Open the catalog to page 5