
nrae 3=0be Rotary: “ARJ” Series
Open the catalog to page 1The Unozawa"ARJ"Three Lobe Positive Displacement Blower are new series roots blowers developed by incorporating Unozawa's extensive experience and technical expertise. This series blower type ARJ employs three lobe rotor, featuring higher performance, lower noise and less vibration It embodies the essence of Unozawa's highly sophisticated technology. The new series blower have been standardized, with a wide applicable working pressure-ranging from low to high. When used for special gas, a mechanical seal can be provided. When applying the Unozawa back-flow cooling system, single stage vacuum...
Open the catalog to page 2Principle Pair of rotors turn in opposite directions inside the casing, maintaining a precision clearance between the side wall of the casing and the two rotors. Gas flows into the blower as the lobe end of each rotor passes the suction port. And gas is transferred from the suction side to the discharge side. It is then discharged, forced towards the high-pressure side. Gas at the suction side is caught in volume"V" surrounded by rotor tips (A), (B) and the casing in process as shown in illustrations (1) and (2) at right, and after step(3),(4) and(5), gas is discharged. With three lobes, this...
Open the catalog to page 3The casing made of cast iron, consisting of the upper suction and the lower horizontal discharge sections, ensures sufficient strength and durability. The bearing are high precision bearings with a load capacity suited for working conditions . Stable performance and long service life are guaranteed. ● Rotor The three lobe rotor made of cast iron or ductile cast iron has good quality subjected to high precision machining. The inside clearances are precision matched and optimum efficiency is guaranteed. In addition, as it is perfectly balanced by means dynamic balancing machine, noise and vibration...
Open the catalog to page 4Shaft Sealing "ARJ" blowers are available with many types of standard shaft sealing. The type of blower shaft sealing is selected according to the gas handled. When handling a special kind of gas, a mechanical seal is provided. Either single or double mechanical seal can be used. Available types of shaft sealing and their general uses are as follows: 3. Four-mechanical seal "B"type: The standard type for blower mainly suitable for blower that handles air. Seal pos ition A Mechanical seals are provided at four points on the back of the bearing. Used for sealing the shaft when handling solvent...
Open the catalog to page 5Back-flow Cooling System The Unozawa Back-f low Cooling System was development by incorporating Unozawa's extensive experience, outstanding achievements and technical expertise in the area of rotary blower and vacuum pump and background of many years of accumulated experience. Back-f low ingeniously utilizes the working pr inciples of a rota ry vacuum pump ( blower)to reduce discha rge temperature, thereby providing many conspicuous advantages noted below, 1. High temperature gases can be handled: 2. Can be used at a higher pressure ratio: When using a vacuum pump or blower at a highpressure...
Open the catalog to page 6Principle of Operation for Back-flow Cooling System What are operating principles of a vacuum pump with back-flow cooling system? The rotor turns in the sequence of(1)to(5). The light section of the drawing indicates the vacuum (suction pressure), while the dark section indicates the discharge pressure. The left side rotor indicates back-flow cooling system function. (1) The rotor tips A and B are positioned to catch suct ion gas in volume" V "(mov ing volume). (2) The rotor has completely caught suction gas in volume" V "and cooled gas whose pre s su re is t he s a me a s t he d is ch a rge...
Open the catalog to page 7Blower Performance Table
Open the catalog to page 11Blower Performance Table
Open the catalog to page 12M=.ftyy Vacuum Pump Performance Table 10 Capacity range (Approximate)
Open the catalog to page 17Note for the perfomance table Capacity on the performance tables represent at the カタログ表 示の空気量は、ロータリブロワについては標準 standard state (temperature at 20℃, absolute pressure 101.3 kPa, relative humidity 65%) . For the vacuum pump, capacity is shown at suction pressure and temperature 20℃ Capacity is generally shown under the condition of following three states and capacity can be converted 6 5 % の 状 態を言 います 。真 空ポンプの 場 合 は吸 込 状 態 (20℃) の風量で示してあります。 一般に風品の表示は次の3種類で、それぞれは換算するこ とが出来ます。 with following formula. 1.Capacity at suction state : Capacity is shown at the suction state of pressure, shown at the temperature...
Open the catalog to page 19With suction silencer Rotating direction Rotating direction Suction port with flange Foundation twit holes Note: I.GD2 represents the value blower shaft. 2.Approx. mass does not include motor mass. 3.Specification may be subject to change without prior notice.
Open the catalog to page 20When using a flexible joint,be sure to provide a support under the discharge silencer(fig2)
Open the catalog to page 21Suction Silencer Type GLT/GLN Note:Above dimensions are subject to change without prior notice.
Open the catalog to page 22Relife valve(with exhaust connecting port)
Open the catalog to page 23Noise Data Noise emissions from the rotary blower fluctuate depending upon blower size, discharge pressure and number of revolutions. The blower noise level is measured according to JIS B 8346 "Noise Level Measuring Method for Blower and Compressors". Noise is measured at 4 6 spots which are 1m apart from the blower depending on its size. Based on the measurement, a typical noise value is calculated n: number of measured values Where L: typical noise level Typical noise values shown below are estimated according to the following formula. according to the JIS mode above.
Open the catalog to page 24Noise Data
Open the catalog to page 25Noise Data
Open the catalog to page 26Unozawa Products 1.Rotary blower(Roots type) 2.Rotary vacuum pump(Roots type) 3.Dry Vacuum pump 4.Mechanical booster 5.Water ring Vacuum pump Inquiries When inquiring about Unozawa three lobe rotary blowers, please furnish the following information 1.Application: Water aeration, pneumatic conveying filter, intra-furnace air blowing, etc... Capacity, suction and discharge conditions(Temperature, pressure) Name of gas, gas constant, corrosiveness, character and quantity of liquid contained Whether Indoors or outdoors, ambient temperature, condition of dust, etc... Type, rpm and frequency of motor...
Open the catalog to page 2710 Pages